Difference between revisions of "CGS ±15V 7x15 power supply"
m (Text replacement - "TOP-3 " to "TO-220 ")
|Line 91:||Line 91:|
Revision as of 15:51, 17 April 2019
CGS14 the CGS ±15V power supply is ideal for a power supply set aside for more "noisy" modules. While this is not essential, it is the easiest way of keeping noise generated by digital modules from the more sensitive analog modules. Different voltage regulators can also be used to give +/- 5 volts, +/- 9 volts, +/- 12 volts or +/- 18 volts, or any other voltage for which 78XX and 79XX regulators are available, as long as the appropriate AC voltage is fed to the unit.
Note: this project may require wiring a transformer to the A.C mains. This is best left to people who are qualified to do so. Where possible, use a plug-pack, wall-wart or line-lump, or other product where the mains wiring has already been done.
How to use this module
This module is designed to connect to various modules using a distribution board such as the Oakley Modular Systems power distribution board or those sold by Synthesis Technology and Blacet Research Music Products. Most of my modules conform to the power supply standard adopted by these manufacturers.
A little on how it works
The circuit is as basic as it gets. The incoming AC power is rectified, then filtered. The filtered DC is regulated by the positive and negative voltage regulators. The regulator minimum load requirements are met by placing a LED and its associated resistor between each output and the 0 volt (ground) line. Capacitors are placed close to the input and output pins of the regulators to improve stability and transient response . Two additional diodes per regulator protect the regulators should the outputs be shorted together, or should a voltage be fed into the output of the power supply. It is very much a standard configuration, detailed in many data books, and no doubt available in as various kits from many places. My first kit of this was produced back in the early eighties, and the circuit hasn't changed, though the PCB layout is new.
When fed from a 30 volt center tapped transformer (15v-0v-15v) you should be able to pull around 200 mA from the PSU without problems. There will be minimal heat generated by the regulators because they will be running close to their minimum voltage drop, though you do risk ripple getting through to the output as the load increases.
When fed from a 36 volt center tapped transformer (18v-0v-18v) you should be able to pull around 600 mA from the PSU without problems. There will be a fair amount of heat generated by the regulators and diodes, so make sure there is adequate airflow around the board. 600 mA is close to the maximum DC current you can draw from this PSU when powered from a 1 amp transformer. You may also wish to use 3300 mfd 25 volt capacitors instead of the specified 2200 mfd.
Drawing more than 600 mA, while possible with a larger transformer, is not recommended, as there is inadequate heatsinking on a number of components, and the electrolytic capacitors are much too close to the heatsinks.
The prototype was tested running at over 800 mA output using 3300 mfd filter capacitors and a 36 volt transformer.
Another factor limiting the maximum current that can be drawn from the unit is the size of the heatsink. With 600 mA being drawn, each regulator can easily be dissipating 6 watts, and will require a heatsink with a rating of 12°C/W or better to operate in an ambient of 25°C. As heat in an enclosed space may well be greater than this, I'd recommend going for the best heatsink of the correct profile you can get. Hobby shops in Australia have them available at 8.5°C/W (50 mm) and 11°C/W (40 mm), depending on the shop, though I have used 63 mm heatsinks I salvaged from old switch-mode power supplies. The profile used is simply listed as PCB mount TO-220 in the local catalogs.
Before you start assembly, check the board for etching faults. Look for any shorts between tracks, or open circuits due to over etching. Take this opportunity to sand the edges of the board if needed, removing any splinters or rough edges.
When you are happy with the printed circuit board, construction can proceed as normal, starting with the diodes and resistors first, followed by the taller components.
Take particular care with the orientation of the polarized components such as the diodes, electrolytics, LEDs and regulators.
The easiest way to install the regulators is to mount them on the heatsinks before installing them and the heatsinks on the PCB. The heatsink mounting holes may need enlarging to accommodate the pins of your selected heatsink. The heatsink I have used is of a very common extruded profile and is available in differing lengths. See above for more details.
This is a guide only. Parts needed will vary with individual constructor's needs.
|2200 uF 35V||2|
|3mm or 5mm LED||2|
|0.156 4 pin connector||1|
- There is a pad available at the center of the star earth for those who need it.
- The negative regulator is at the TOP of the board, so the schematic layout is a mirror of the actual PCB layout when viewed from above.
- The LEDs could be mounted on the front panel of the synthesizer as indicators.
- Though I have specified 1N4004 diodes, any power diode with at least 100V PIV and a current rating of 1 amp could be substituted.
- If you are planning on running this unit hard, it may be appropriate to use a pair of chassis mounted electrolytic capacitors for the filter capacitors, as the heat from the heatsinks may cook them if they are left on the PCB. Keep the leads as short as possible.
- If using +/- 18 volt regulators you may need to use 50 volt electrolytics, as depending on your chosen transformer, the rectified DC may be too close to the limit of 35 volt electrolytics for comfort.
- Can this PCB be used with a conventional AC-wall-wart (two AC wires out)? A center tapped transformer is better, though it is possible to use a wall-wart between CT (the 0V connection on the PCB) and one 18V AC connection. The result will be half wave rectification. If you use larger caps (3300uf) and limit the loading, you will be okay. My test bench power supply had been running like this for years. Watch the output with a CRO if you can, to find the limit. If you really wanted to, two wall-warts could be used, each between one of the 18V connections, and commoned at the CT connection. You'd have to make sure the phases were right though. With the one wire from each of the wall-warts connected together, measuring across the other two wires should give you something like 36 volts. If it gives you 0 volts, you will need to swap the wires from one of the wall-warts.
- I power my more critical circuits from a Power One unit, essentially identical to the MOTM unit available from Synthesis Technology, and, without the mounting plate and distribution board, from many other suppliers. While I haven't tried it, the Blacet Research Music Products PSU also looks like a good choice.
- +/- 15 Volt Power Supply (archived) by Ken Stone, 2001, with permission of the author
- CGS Synth discussion group, for discussion of locating parts, modifications and corrections etc.