Open main menu

CGS analog switch matrix (previous version)

Cgs photo cgs55 asm.jpg

CGS55 the CGS analog switch matrix (v1.0) is a complex router, allowing one input to be switched between four outputs, or vice versa, or even to route one signal through one of four external effects (e.g. wave multipliers, filters etc.). It can also be used as four independent analog switches.

All analog switches are independently addressed, so combinations of these arrangements are also possible. Further enhancing this is that the common input and output external are to the main switching matrix. There is also a separate mixer than can be used for recombining signals when routing between different effects, or the mixer can be used as an independent general purpose DC coupled unity gain mixer.

Unlike the previous version, where only an inverting common input was available, this version has both non-inverting and inverting common inputs.

The analog switch is DC coupled so can be used for both control voltages and audio signals.

Suitable drivers for one-at-a-time switch control include the CGS gate sequencer and the CGS weighted random switch. Any module, or combination of modules, that generates gate signals can be used to drive the matrix if having more than one switch closed at time is acceptable or desirable.

The CGS weighted random switch is a companion module, as it can be directly connected while leaving the standard gate inputs functional.

While untested, the module should work on +/-12 volts.

A little on how it works

 
The schematic of the Analog Switch Matrix. Click through to view full sized.
 
Power rail connections

Construction

 
The component overlay.

Before you start assembly, check the board for etching faults. Look for any shorts between tracks, or open circuits due to over etching. Take this opportunity to sand the edges of the board if needed, removing any splinters or rough edges.

When you are happy with the printed circuit board, construction can proceed as normal, starting with the resistors first, followed by the IC socket if used, then moving onto the taller components.

Take particular care with the orientation of the polarized components such as electrolytics, diodes, transistors and ICs.

When inserting ICs into sockets, take care not to accidentally bend any of the pins under the chip. Also, make sure the notch on the chip is aligned with the notch marked on the PCB overlay.

Weighted Random Switch

As mentioned, this switch matrix can be used to expand the switching capabilities of the CGS weighted random switch.

Joining the two is relatively straight forward.

On the CGS51 board there is an area of the board marked off with a thin line, containing the text "The Neurotic". All parts are to be omitted from this area as they are not needed.

There are numerous pads around this area marked with a white outline. Of interest are those marked 0, 1, 2, 3, and C. These connect directly to the corresponding pads on the CGS55 board, thus linking the two together.

It is possible to omit the power supply parts from one of the two PCBs and link the pads marked +VE, -VE, 0V and -0.6V as well. If it is easier, there is no reason why the power supply parts can't be installed on both boards, with each board being fed via the MOTM/Modcan connectors.

These pads line up on the two boards, so it would be possible to mount the boards one on top of the other, with a plug and socket arrangement between the two boards to allow easy servicing. These plugs and sockets could be made from machine socket pins or similar. Again, this is only optional, and simply running insulated wires between the corresponding pads may prove more reliable and easier to build.

A switch could be placed between the C pads, allowing the switch matrix to be isolated from the weighted random board when the switch matrix is needed without the random function.

Parts list

This is a guide only. Parts needed will vary with individual constructor's needs.

Part Quantity
Capacitors
47pF ceramic or sim 14
0.1uf/100n monolythic ceramic or sim 8
10uF 25V(or higher) 3
Resistors
330Rk 6
2k2 2
10k 4
15k 1
100k 49
Semi's
1N4148 14
4066 1
TL072 7
TL074 1
Misc
Ferrite bead (or 10R resistor) 1
0.156 4 pin connector 1
CGS55 v2.0 PCB 1

Notes

  • PCB is 6" x 2" with 3mm mounting holes 0.15" in from the edges.

CC-BY-NC

Readers are permitted to construct these circuits for their own personal use only. Ken Stone retains all rights to his work.

See also

References

External links