Difference between revisions of "CGS bus driver"

Jump to navigation Jump to search
 
Line 115: Line 115:
  
 
[[Category:CGS CV processors]]
 
[[Category:CGS CV processors]]
 +
[[Category:CGS general and accessories]]

Latest revision as of 20:10, 7 June 2019

Cgs photo cgs98 busdriver.jpg

The CGS98 the CGS bus driver is a buffered bus for distributing CVs, or even audio to several modules, or even to several cabinets. In the basic configuration, it has four buffers, each of which (through the use of a CGS98 expansion) also offers inversions of these voltages. In the advanced configuration, input 1 is added to the signals of inputs 2, 3 and 4. As such, a root note can be fed into input 1, while sequencers are fed into the other inputs. Changing the voltage on input 1 would then change the root of all three of the sequences, allowing them to follow the root pitch. This was developed due to the drastic shortage of CV inputs on many Eurorack VCO modules.

An optional expansion board allows the buffered outputs to be bussed to other locations in the synthesizer. Also on the expansion board are inverted versions of the incoming signals. The non-inverted outputs on the expansion boards are hard-wired to the outputs on the driver board. The inverted outputs 2, 3 and 4 are not offset by the voltage on input 1, irrespective of whether the internal links are installed or not.

A little on how it works

The schematic for the Bus Driver module.
The main bus driver PCB contains all of the electronics.
The CGS93 trunk PCB is used for the extended outputs.
Pad identification
Pad ID Function
0V 0V/GND power rail for use with Banana installations

Construction

Before you start assembly, check the board for etching faults. Look for any shorts between tracks, or open circuits due to over etching. Take this opportunity to sand the edges of the board if needed, removing any splinters or rough edges.

Jack centers are at 1/2" spacing. The board will fit behind Euro and Frac rack panels.

The light colored surface mount parts are 39pF to 47pF. The dark ones are 100nF.
Cgs photo cgs98 busdriver2.jpg

Surface mount capacitors of 1206 or 805 are used on the rear of the PCB. See above.

For best results, hand match the resistors. This may necessitate you buying 100 resistors to sort through.

Use IC sockets. Once the unit is assembled, power it, with no inputs connected. Check the voltages at the outputs. Ideally, they will all be at zero. If an output is too far from zero, replace the corresponding chip. (0.083V = a semitone, so 0.005 V would be noticeable.) That chip can be used in other projects where such an offset is not a problem.

If using a boxed header for the power connection, it will need a little filing so it clears the leads of the Ferrite beads.

Between each set of pads for the mounting of the Cliff jacks, there is a large pad with two holes. This is so banana jacks can easily be mounted on the side of the board without the overlay. A short length of wire can be folded, looped through the banana jack's hole, then through the holes on the PCB, where it can be twisted to hold the jack in place while you solder it. The twist can then be trimmed back. As banana jacks have no earth connection, one has been provided on the PCB itself. Hook this to the nearest convenient power supply 0V/GND point on your panel. This will ensure the shield wires in the ribbon cable(s) are earthed.

If using banana jacks with the Euro panel, the jacks need to be mounted on the other side. A small portion needs to be trimmed from the tab of the jack to prevent it shorting against other tracks. See the photos on the CGS93 page.

The three jumpers (J2,3,4) are to allow the output of the first driver to be disconnected from the other three drivers. You can use wire links, or removable jumpers.

The panel has two sides, one for use as the input panel, or as a stand-alone module, the other for the bus outputs, if used.

Cgs photo cgs33euro w.jpg

To use the CGS98 as a bus driver, several CGS93 need to be used, and linked with a cable such as the one shown above, or using short, two-plug cables alternating between the top and bottom sockets. In this configuration, the multiples will be horizontal. See the CGS99 bus expansion port for a convenient way of connecting between cases.

Both of these methods of interconnection are valid. On the CGS93, the box headers have identical pinouts and are in parallel. The lower header on the CGS98 is a standard Euro power connector.

Parts list

This is a guide only. Parts needed will vary with individual constructor's needs.

Driver
Part Quantity
Resistors (1% metal film)
330R 8
100k 19
Capacitors
47pF 1206 8
100nF 1206 8
10uF electrolytic 2
Semi's
TL072 4
Misc.
2 pin header and link 3
Ferrite bead 2
16pin (2 x 8 pin) 90° box headers 2
Cliff CL1384 (S6) 3.5mm jack sockets 8
CGS98 V1.0 PCB set 2
Expansion
Part Quantity
16pin (2 x 8 pin) 90° box headers 2
Cliff CL1384 (S6) 3.5mm jack sockets 8
CGS98 expansion PCB set 2

CC-BY-NC

Readers are permitted to construct these circuits for their own personal use only. Ken Stone retains all rights to his work.

See also

References

  • Bus Driver. (archived) by Ken Stone, 2013, with permission of the author

External links