CGS gated comparator (previous version)
The idea for CGS13 the CGS gated comparator project came when I was listening to some music in which part of the background was jumping between octaves in a semi-random fashion. Feeding noise into a comparator was my immediate thought, but I soon realized this wasn't going achieve what I wanted. I needed to be able to control when these jumps could occur. As such, some form of memory element was required, into which the level could be clocked when required.
I have used an 8 stage digital shift register as the memory element. Each clock pulse, the remembered level (logic 0 or logic 1) is moved into the next stage "bucket brigade" fashion, and the new value stored in the first memory cell. The result is a random level (on or off) at a predetermined time at the first output, plus time delayed versions of previous levels across the remaining outputs.
As well as the 8 shifted gate outputs available, the raw comparator output is also available. The status of each of the outputs is displayed by a LED, making adjusting the unit so much easier.
There is also a secondary voltage control input so the comparator break/reference point can be varied by an external control voltage.
On top of all this, there is a D/A converted connected to the outputs of the shift register, with the last 4 bits capable of being switched in or out. This gives some great little melodies or sequences. They will depend largely on what is fed into the shift register, though due to the configuration will always have a certain flavor. There is an inverted output for this as well. When the resultant voltage is fed to a VCO, effects from subtle semi-random melodies to 70s sci-fi computer sounds can be generated.
While untested, the module should work on +/-12 volts.
How to use this module
Connect the input to a noise source, LFO, VCO or other signal source. Connect a LFO or similar clock signal from a sequencer, etc. to the clock input. Connect the shift register outputs as required to VCOs, VCFs or other clocked modules, and/or connect the CV (RV and RVI) outputs to a module that requires a CV input.
The unit can also be used as a simple gate delay, where the delay is controlled by the frequency of the clock signal. The length of the resulting delayed gate signal would of course be a multiple of the clock period.
A little on how it works
The circuit consists of two comparators, one with it's sensing point adjustable by a front panel knob an and external CV. This is for processing the input signal, and the other to square up the gate or clock signal and provide some isolation for the CMOS shift register (4015).
Each of the digital outputs is buffered by a transistor/resistor buffer, of which a LED is part.
The two shift registers in the 4015 are clocked from the same source. The fourth output of the first shift register needs to be slightly delayed to ensure reliable loading of the second shift register.
The outputs of all of the shift register stages are also fed to D to A converter consisting of an R/2R resistor ladder and an op amp wired as a voltage follower. A second op amp provides an inverted output.
Before you start assembly, check the board for etching faults. Look for any shorts between tracks, or open circuits due to over etching. Take this opportunity to sand the edges of the board if needed, removing any splinters or rough edges.
When you are happy with the printed circuit board, construction can proceed as normal, starting with the resistors first, followed by the IC sockets if used, then moving onto the taller components.
Take particular care with the orientation of the polarized components, the electrolytics, LEDs, diodes, transistors and ICs.
When inserting the ICs in their sockets, take care not to accidentally bend any of the pins under the chip. Also, make sure the notch on the chip is aligned with the notch marked on the PCB overlay.
Although an LM358 is specified in the diagram and on the PCB overlay, better results will be achieved using a TL072 in its place.
Being the optimist I am, I left the RC delay between the two stages of the 4015 off the circuit board, only to find the first 4015 I tried needed it. See the diagram above for details of the modification. The REV1 version of this board has the modification included, so no track cutting is required.
This is a guide only. Parts needed will vary with individual constructor's needs.
|10k Lin pot||1|
|BC547 (or sim)||9|
|BC557 (or sim)||1|
|Ferrite bead (or 10R resistor)||2|
|0.156 4 pin connector||1|
- A 10 to 22 ohm resistor can be used instead of the ferrite bead. If you don't care about power-rail noise, just use a link instead.
- If you would rather the inverted CV output (RVI) operated above 0 volts, a resistor can be soldered between pin 2 of the TL072 and the negative rail. Try a value around 47k to 100k.
Readers are permitted to construct these circuits for their own personal use only. Ken Stone retains all rights to his work.
- Gated Comparator for music synthesizers (archived) by Ken Stone, 2001, with permission of the author
- CGS Synth discussion group, for discussion of locating parts, modifications and corrections etc.