Difference between pages "Jumper wire" and "File:8c58ae2d322a33f3036800d96db0e91a.png"

(Difference between pages)
Jump to navigation Jump to search
 
(== Summary == Importing file)
 
Line 1: Line 1:
 
== Summary ==
[[File:C4128_large_jumper_wires_20cm_m-f_pack_10.jpg|thumb|right|200px|Male to female jumper wire strip]]
 
  +
Importing file
[[File:Jumper Wires with Crocodile Clips.jpg|thumb|right|200px|Jumper wires with crocodile clips, aka test leads.]]
 
[[File:Arduino_Breadboard_ATmega328P_USB2Serial.jpg|thumb|right|200px|A ribbon cable connects the pin sockets of an Arduino USB 2 Serial micro to a breadboard and wire jumpers make interconnections on the breadboard.]]
 
A '''jumper wire''' also known as '''jumper link''', '''jumper''', '''jump wire''' or '''DuPont cable''' is a connecting wire, bare at the ends or terminated with some type of connector.
 
 
== Use in prototyping ==
 
Jumper wires of insulated 26[[American wire gauge|AWG]] wire terminated with [[crimping|crimped]] pins or sockets in plastic housing are used to make connections between [[pin headers]] or sockets. With 2.5 mm (0.1 inch) housing they're suitable for interfacing single board computers like the [[Arduino]] and [[Raspberry Pi]]. These will also fit without damage to interconnect the components on solderless [[breadboard]] although here 22 AWG solid-core hookup wire with bare ends can be used instead.<ref>[https://www.rapidonline.com/jumper-wires-for-breadboard-arduino-raspberry-pi-olimex-etc-544268 Jumper Wires for Breadboard, Arduino, Raspberry Pi, Olimex, etc.], Rapid Electronics</ref>
 
 
== DuPont crimp connectors ==
 
A DuPont crimp consists of two parts, 0.1” (2.54mm) housing and separate metal crimp terminal. The AWG for wire generally used is 22, 24, 26 or 28 (standard ribbon cable) and a maximum diameter of 1.57mm.<ref>Molex data sheet [http://www.molex.com/webdocs/datasheets/pdf/en-us/0008500114_CRIMP_TERMINALS.pdf 08-50-0114]</ref><ref>Molex data sheet [http://www.molex.com/webdocs/datasheets/pdf/en-us/0008520072_CRIMP_TERMINALS.pdf 08-52-0072]</ref>
 
 
Using the proper crimping tool makes a good crimp joint easy. A properly crimped joint does not need soldering and is more than strong enough.<ref>[http://renoirsrants.blogspot.co.uk/search/label/Crimping Crimping], by Dave Renoir, 20 October 2011</ref> Most crimp terminals are designed to be crimped, not soldered. Soldering a crimped terminal may weaken the mechanical connection, reduce electrical conductivity, and damage the terminal. As a general rule, you should not solder a crimp terminal.<ref>[http://www.virginiawind.com/tips/060801_02.asp Making the Connection: Solder vs. Solderless Terminals] by Jerry Sussman</ref>
 
 
== See also ==
 
* [[Wire link]]<!-- on a PCB -->
 
* Wikipedia:[https://en.wikipedia.org/wiki/Jumper_(computing) Jumper (computing)]
 
 
== References ==
 
{{reflist}}
 
 
== External links ==
 
* [https://forum.arduino.cc/index.php?topic=376971.0 FYI Making DuPont jumper wires.], Arduino Forum, Feb 2016
 
* [https://electronics.stackexchange.com/questions/179179/what-is-the-official-name-for-these-jumper-wires/179183#179183 What is the official name for these jumper wires?], StackExchange EE
 
=== Suppliers ===
 
* [http://www.mouser.co.uk/Tools-Supplies/Prototyping-Products/Jumper-Wires/_/N-bkrh0 Mouser]
 
* [https://www.digikey.com/products/en/prototyping-products/jumper-wire/640 Digi-Key]
 
* [https://www.rapidonline.com/jumper-wires-for-breadboard-arduino-raspberry-pi-olimex-etc-544268 Rapid]
 
 
[[Category:Connectors]]
 
[[Category:Prototyping]]
 

Latest revision as of 19:48, 17 April 2021

Summary

Importing file