m
Text replacement - " - archived" to " - archived"
No edit summary |
m (Text replacement - " - archived" to " - archived") Tag: Manual revert |
||
| (16 intermediate revisions by the same user not shown) | |||
Line 44:
* 1M – Log response – Finer control near center of rotation. Greater sensitivity towards ends of travel.
=== Notes ===
* With no inputs connected, the AND module output will sit at approx. +10V.
* With no inputs connected, the OR module output will sit at approx. -10V.
Line 50:
* If you wish to have a panel mounted pot to set the maximum voltage for the AND/NAND module and the minimum for the OR/NOR module, they can be wired in with the pots connected between the outputs of the transistor regulators (+10V and -10V) with their wipers fed via a signal diode to pin 10 of the corresponding voltage follower. This is possible because the "perfect diode" is not required in this circumstance. Use a pot of 5k or 10k to get a more linear response. Higher values will work, but the pot response will be decidedly curved. Additional "inaccurate" inputs for other voltage sources could also be added in a similar manner – with a diode and series 1k resistor wired into the corresponding voltage follower. These "inaccurate" inputs will be affected by the output impedance of what is driving them, so do not be surprised if it responds differently when connected to different modules.
* While untested, the module should work on +/-12 volts, though you will need to adjust the resistor networks for the +/- 10 volt regulators if you wish to maintain the range (use 2k2 resistors instead of the 4k7 resistors for the two transistor base resistors).
* A 10 to 22 ohm resistor can be used instead of the ferrite bead. If you don't care about power-rail noise, just use a link instead.▼
== Parts list ==
Line 57 ⟶ 56:
{|style="border:1px solid #BBB; display:inline-table; margin-right:25px;"
| colspan="2"|Versions prior to 1.2
|-
| Part||align=right|Quantity
Line 92 ⟶ 89:
! colspan="2" align=center|Misc.
|-
| Ferrite
|-
| 0.156 4 pin connector||align=right|1
Line 101 ⟶ 98:
{|style="border:1px solid #BBB; display:inline-table;"
| colspan="2"|Version 1.2
|-
| Part||align=right|Quantity
Line 142 ⟶ 137:
! colspan="2" align=center|Misc.
|-
| Ferrite
|-
| 0.156 4 pin connector||align=right|1
Line 148 ⟶ 143:
| CGS26 v2.1 PCB||align=right|1
|}
=== Notes ===
▲* A 10 to 22 ohm resistor can be used instead of the ferrite bead. If you don't care about power-rail noise, just use a link instead.
== CC-BY-NC ==
Readers are permitted to construct these circuits for their own personal use only. Ken Stone retains all rights to his work.
== See also ==
Line 154 ⟶ 155:
== References ==
''[https://web.archive.org/web/
{{reflist}}
== External links ==
* [http://groups.yahoo.com/group/cgs_synth CGS Synth discussion group], for discussion of locating parts, modifications and corrections etc.
* [http://bompiler.com/pcb/cgs26 CGS26 v1.21 BOM] at BOMpiler
=== Suppliers ===
* [http://www.elby-designs.com/webtek/cgs/cgs26/cgs26_analogic.html CGS26 Analog Logic Voltage Processor], revision 1.21, Elby Designs
[[Category:CGS
| |||