Rescuing 1 sources and tagging 0 as dead.) #IABot (v2.0.9.3
m (added Category:Effects using HotCat) |
(Rescuing 1 sources and tagging 0 as dead.) #IABot (v2.0.9.3) |
||
| (11 intermediate revisions by 2 users not shown) | |||
Line 1:
A '''spring-line reverb tank''' is a simple [[electro-mechanical]] means of adding a reverberation effect onto an (electrical) audio signal.
A spring-line reverb tank is a simple electro-mechanical means of adding a reverberation effect onto an (electrical) audio signal. The unit consists of a number of springs with a transducer at either end. At the input, an electro-magnetic coil is used to turn the (AC) electrical signal applied into a back-and-forth twisting motion on a small piece of magnetic material on the end of the spring. The mechnical vibrations travel down the spring and are turned back into an electrical signal by a similar magnet and coil device (acting as a pick-up) at the other end. Some of the vibrations will 'bounce back' and travel up and down the spring repeatedly, which is what gives rise to the reverberation effect.▼
== Description ==
▲
By varying the number of springs, and the mechnical properties of the springs, the 'quality' and duration of the reverberation can be altered. Some units use pairs of springs which are wound in opposite directions, as apparently this can mitigate some of the 'sproingy' effects these units can suffer from (whilst others appreciate the 'charm' this brings to the sound of a spring reverb!).
== Mounting the tank ==
Because the springs themselves look like
▲Because the springs themselves look like inductors to any nearby electro-magnetic signals that may be floating around, they are ''very'' susceptible to picking up interference from power supplies and the like within a modular set-up. This presents a perennial problem of how/where to mount the tank inside/outside the case in order to minimise mains hum from being picked-up by the unit. Trial and error is really the only option, though there are many ideas to be found by searching the forum archives - these threads may be a starting point:
▲[http://www.muffwiggler.com/forum/viewtopic.php?t=2700 A-199 Spring Reverb]
▲[http://www.muffwiggler.com/forum/viewtopic.php?t=17496 noisy A-199]
== Replacing the Doepfer A-199 spring tank ==
The
:2 – Medium decay
The two most important ones are the input and output
▲The Belton tank used as standard in the Doepfer A-199 is a BMN3BB2C1B, which breaks down as:
▲::BMN3 Belton, mini, new, short 3-spring<br />
▲::B - input impedance 190Ω<br />
▲::B - output impedance 2575Ω<br />
▲::C - input insulated, output ground<br />
▲::1 - no lock<br />
▲::B - horizontal mount, open down<br />
▲The two most important ones are the input and output impedances, and any replacement should try and match these two closely in order that the circuit functions as originally intended (different input impedances have different input drive level requirements, so if one of a different impedance is used, the tank may be either under- or overdriven, most likely resulting in poor performance, either a weedy signal and/or distortion of some type).
The 'connections' specifier, the 'C', is unlikely to be critical: in the Doepfer circuit the input is grounded in any case, so using a 'B' type (input grounded/output insulated) will not cause any problems; use of an 'A' (both grounded) or a 'D' (both insulated) will not cause any problems from an electrical standpoint, but may not be advisable from a noise point of view, i.e. leaving the case floating ('D'), may make it more susceptible to hum pick-up, and grounding both sides ('A'), may have implications for noise due to the very small signal levels at the output - without trying it, I wouldn't like to say!▼
As for the last two characters: the '1' = 'no lock', the only place you'll likely to see one with a lock (which simply holds the springs safely for transport) is in an ancient tank on one of the auction sites; the final letter, the mounting orientation, refers to the preferred mounting method to give optimal performance - I'm certain most people ignore this, and I've never seen an issue reported for which the root cause was not having the tank correctly orientated (apparently the 'bobbins' either end, with the spring-mounted magnets inside them, perform better some ways than others).▼
Thus an example suitable replacement would be an Accutronics '''9BB3C1B''', but any v'''BB'''wxyz, where v, w, x, y, z are any of the possible alternatives for that character position (with the proviso on the 'x' connection-specifier, the 'C', noted above), will be fine!▼
== Manufacturers ==▼
[http://www.accutronicsreverb.com/ Accutronics] have been a major player for many years, but have recently been taken over by Belton.▼
The [http://www.belton.co.kr/index.php?mm_code=75 Belton] range of tanks include many similar to the Accutronics units, but also include 'mini' tanks, which are favoured by some Eurorack makers' reverb modules.▼
These [http://www.tubeampdoctor.com/en/shop_Reverb_Cans_TAD_Reverb_Cans/ Tube Amp Doctor] tanks have recently come to light, with very similar looking tanks/specs to the other makes.▼
Another brand of tanks has recently emerged - [http://www.amplifiedparts.com/products/amp_parts?&filters=MOD+Reverb+Tanks MOD reverb tanks]. These are apparently meant to be clones of the early Accutronics tanks: they are made for [http://www.cedist.com CE Distribution], who also seem to be the same people as [http://www.tubesandmore.com Antique Electronic Supply ('tubesandmore.com')], and [http://www.modkitsdiy.com Mod Kits DIY], as well as [http://www.amplifiedparts.com Amplified Parts] - the similarities in the webpages are obvious, and the [http://www.amplifiedparts.com/tech_corner/spring_reverb_tanks_explained_and_compared technical page] mentioned in the intro above is available at several of these sites, and also contains a summary comparison between the Accutronics, Belton, and MOD tanks.▼
Take care with some of these: some will be designed to interface to guitar-level signals (I'm guessing tens to hundreds of ''millivolts''?), and so may need re-scaling for use with general synthesizer-level signals of ''volts'' up to ''10 volts'' or more! ▼
Useful [http://www.accutronicsreverb.com/main/?skin=sub05_08.html application notes] at the Accutronics site.▼
▲The 'connections' specifier, the 'C', is unlikely to be critical: in the Doepfer circuit the input is grounded in any case, so using a 'B' type (input grounded/output insulated) will not cause any problems; use of an 'A' (both grounded) or a 'D' (both insulated) will not cause any problems from an electrical standpoint, but may not be advisable from a noise point of view, i.e. leaving the case floating ('D'), may make it more susceptible to hum pick-up, and grounding both sides ('A'), may have implications for noise due to the very small signal levels at the output
A couple of simple and more complex circuits [http://sound.westhost.com/project34.htm]▼
▲As for the last two characters: the '1' = 'no lock', the only place
Scan of a [http://vintageradio.me.uk/electronics/reverb72.htm Practical Wireless article] from 1972▼
▲Thus an example suitable replacement would be an [[Accutronics
== References ==
* [https://web.archive.org/web/20110819081810/http://wiki.modwiggler.com/wiki/Spring-line_Reverb_Tanks Spring-line Reverb Tanks] by Tim Stinchcombe, Mod Wiggler wiki
== External links ==
The [http://www.tellun.com/motm/diy/tln156/TLN-156.html Tellun Neural Agonizer] which uses two tanks▼
* [https://web.archive.org/web/20120111214611/http://www.amplifiedparts.com/tech_corner/spring_reverb_tanks_explained_and_compared Spring Reverb Tanks Explained and Compared], a thorough introduction ''and'' detailed description of spring reverb tanks
▲=== Manufacturers ===
▲* [http://www.accutronicsreverb.com/ Accutronics] have been a major player for many years, but have recently been taken over by Belton.
▲* The [https://web.archive.org/web/20130616164602/http://www.belton.co.kr/index.php?mm_code=75 Belton] range of tanks include many similar to the Accutronics units, but also include 'mini' tanks, which are favoured by some Eurorack makers' reverb modules.
▲* These [https://web.archive.org/web/20121028204959/http://www.tubeampdoctor.com/en/shop_Reverb_Cans_TAD_Reverb_Cans/ Tube Amp Doctor] tanks have recently come to light, with very similar looking tanks/specs to the other makes.
▲* Another brand of tanks has recently emerged
=== Schematics ===
▲Take care with some of these: some will be designed to interface to guitar-level signals (
▲* Useful [https://web.archive.org/web/20110425065824/http://www.accutronicsreverb.com/main/?skin=sub05_08.html application notes] at the Accutronics site.
▲* A couple of simple and more complex circuits [https://web.archive.org/web/20110510103051/http://sound.westhost.com/project34.htm Spring Reverb Unit For Guitar or Keyboards]
▲* Scan of a [http://vintageradio.me.uk/electronics/reverb72.htm Practical Wireless article] from 1972
* [https://web.archive.org/web/20130421035909/http://homepage.ntlworld.com/henry01/spring_reverb/spring_reverb.htm Triple Spring Reverberation Unit], a more involved circuit using three tanks.
* [http://modularsynthesis.com/modules/DJB-002/djb002.htm DJB-002 Mixer, Spring Reverb, & A-440 Standard module] by David Brown
▲* The [http://www.tellun.com/motm/diy/tln156/TLN-156.html Tellun Neural Agonizer] which uses two tanks
[[Category:Effects]]
| |||