Rescuing 1 sources and tagging 0 as dead.) #IABot (v2.0.9.3
No edit summary |
(Rescuing 1 sources and tagging 0 as dead.) #IABot (v2.0.9.3) |
||
(8 intermediate revisions by 2 users not shown) | |||
Line 1:
A '''spring-line reverb tank''' is a simple [[electro-mechanical]] means of adding a reverberation effect onto an (electrical) audio signal.
== Description ==
The unit consists of a number of springs with a [[transducer]] at either end. At the input, an electro-magnetic coil is used to turn the ([[AC]]) electrical signal applied into a back-and-forth twisting motion on a small piece of magnetic material on the end of the spring. The mechnical vibrations travel down the spring and are turned back into an electrical signal by a similar magnet and coil device (acting as a pick-up) at the other end. Some of the vibrations will
By varying the number of springs, and the mechnical properties of the springs, the 'quality' and duration of the reverberation can be altered. Some units use pairs of springs which are wound in opposite directions, as apparently this can mitigate some of the 'sproingy' effects these units can suffer from (whilst others appreciate the 'charm' this brings to the sound of a spring reverb!).
== Mounting the tank ==
Because the springs themselves look like [[inductor]]s to any nearby electro-magnetic signals that may be floating around, they are ''very'' susceptible to picking up [[interference]] from [[power supplies]] and the like within a [[modular]] set-up. This presents a perennial problem of how/where to mount the tank inside/outside the [[case]] in order to minimise [[mains hum]] from being picked-up by the unit. Trial and error is really the only option, though there are many ideas to be found by searching the
* [
* [
== Replacing the Doepfer A-199 spring tank ==
The tank used as standard in the [[Doepfer A-199]] is a [[Belton BMN3|Belton BMN3BB2C1B]] which breaks down as:
:BMN3
:B
:B
:2
:C
:1
:B
The two most important ones are the input and output [[impedance]]s, and any replacement should try and match these two closely in order that the circuit functions as originally intended (different input impedances have different input drive level requirements, so if one of a different impedance is used, the tank may be either under- or overdriven, most likely resulting in poor performance, either a weedy signal and/or [[distortion]] of some type).
Line 25:
The 'connections' specifier, the 'C', is unlikely to be critical: in the Doepfer circuit the input is grounded in any case, so using a 'B' type (input grounded/output insulated) will not cause any problems; use of an 'A' (both grounded) or a 'D' (both insulated) will not cause any problems from an electrical standpoint, but may not be advisable from a noise point of view, i.e. leaving the case floating ('D'), may make it more susceptible to hum pick-up, and grounding both sides ('A'), may have implications for noise due to the very small signal levels at the output.
As for the last two characters: the '1' = 'no lock', the only place there is likely to be one with a lock (which simply holds the springs safely for transport) is in an ancient tank on one of the auction sites; the final letter, the mounting orientation, refers to the preferred mounting method to give optimal performance
Thus an example suitable replacement would be an [[Accutronics
== References ==
* [https://web.archive.org/web/20110819081810/http://wiki.
== External links ==
* [https://web.archive.org/web/20120111214611/http://www.amplifiedparts.com/tech_corner/spring_reverb_tanks_explained_and_compared Spring Reverb Tanks Explained and Compared], a thorough introduction ''and'' detailed description of spring reverb tanks
=== Manufacturers ===
* [http://www.accutronicsreverb.com/ Accutronics] have been a major player for many years, but have recently been taken over by Belton.
* The [https://web.archive.org/web/20130616164602/http://www.belton.co.kr/index.php?mm_code=75 Belton] range of tanks include many similar to the Accutronics units, but also include 'mini' tanks, which are favoured by some Eurorack makers' reverb modules.
* These [https://web.archive.org/web/20121028204959/http://www.tubeampdoctor.com/en/shop_Reverb_Cans_TAD_Reverb_Cans/ Tube Amp Doctor] tanks have recently come to light, with very similar looking tanks/specs to the other makes.
* Another brand of tanks has recently emerged
=== Schematics ===
Take care with some of these: some will be designed to interface to guitar-level signals (
* Useful [https://web.archive.org/web/20110425065824/http://www.accutronicsreverb.com/main/?skin=sub05_08.html application notes] at the Accutronics site.
* A couple of simple and more complex circuits [https://web.archive.org/web/20110510103051/http://sound.westhost.com/project34.htm Spring Reverb Unit For Guitar or Keyboards]
* Scan of a [http://vintageradio.me.uk/electronics/reverb72.htm Practical Wireless article] from 1972
* [https://web.archive.org/web/20130421035909/http://homepage.ntlworld.com/henry01/spring_reverb/spring_reverb.htm Triple Spring Reverberation Unit], a more involved circuit using
* [http://modularsynthesis.com/modules/DJB-002/djb002.htm DJB-002 Mixer, Spring Reverb, & A-440 Standard module] by David Brown
* The [http://www.tellun.com/motm/diy/tln156/TLN-156.html Tellun Neural Agonizer] which uses two tanks
[[Category:Effects]]
|