CGS Serge dual channel stereo mixer

Revision as of 22:15, 23 January 2019 by InternetArchiveBot (talk | contribs) (Rescuing 1 sources and tagging 0 as dead. #IABot (v2.0beta10ehf1))
Jump to navigation Jump to search

CGS101 the CGS Serge dual channel stereo mixer (DCSM) module is a variation of the Serge Dual Channel Stereo Mixer, built using the CGS101 Quad VCA and the CGS102 Equal Power Panner drivers.

The unit will run on either +/-12 volts or +/-15 volts.

Description

The dual channel stereo mixer (DCSM) is an alternative output VCA/mixer/panner for two and three-panel systems. The dual channel stereo mixer is used for the standard output level control (or enveloping) and for voltage controlled panning. The DCSM has two independent channels for stereo panning. Each channel in the DCSM has two VC inputs, one for amplitude control and one for panning. The panning controls are opposite for the two channels, so that if a single control voltage is used, the output signals will pan in opposite directions. Auxiliary inputs are used to feed other signals into the outputs of the module. Signals applied here will not be affected by knobs or control voltages applied to the module. These are mainly useful for linking other mixers (either manual or voltage controlled) to the output bus. The output is available at a pair of banana Jacks (for routing the signals to other modules within the synthesizer), and at mini-Jacks (for connecting to external amplifiers, tape decks, and other equipment).[1]

A little on how it works

The schematic for Serge Dual Channel Stereo Mixer module.

Construction

The component overlay for the VER1.0 PCB. Click through for an enlarged, printable version. Print at 300dpi.
The CGS101 loaded with eight sub modules.

The CGS101 DCSM uses four CGS108 Serge gain cells as it's voltage controlled elements. Refer to the CGS108 page for construction details.

It also uses two sets of CGS102 CGS Serge equal power panner boards. Refer to the CGS102 page for construction details. These submodules should be the last things you install on the CGS101 PCB.

Before you start assembly, check the board for etching faults. Look for any shorts between tracks, or open circuits due to over etching. Take this opportunity to sand the edges of the board if needed, removing any splinters or rough edges.

When you are happy with the printed circuit board, construction can proceed as normal, starting with low profile components such as resistors and diodes first, followed by successively taller components.

Take particular care with the orientation of the polarized components, such as ICs, electrolytics, diodes, and transistors.

When inserting the ICs in their sockets, if used, take care not to accidentally bend any of the pins under the chip. Also, make sure the notch on the chip is aligned with the notch marked on the PCB overlay.

The first time you power it up, I would suggest you do so with 22 ohm resistors in series with the positive and negative power rails. This should save the chips if you have made a blunder.

On the CGS101 VER1.0 PCB there are some corrections required.

  • Four 5k6 resistors need to be installed on the rear of the PCB. Each resistor goes between pins 7 (CV) and 8 (0V) of one of the CGS108 submodules.
  • Two connections to each CGS102B submodule need to be reversed. Fortunately this can be done entirely on the rear of the PCB by cutting the tracks in the areas shown in light green on the diagram below. After some solder mask is scraped from the remaining track stubs, (shown in copper below) six links can be added. The four links shown in blue can actually be replaced with two short lengths of component wire offcuts. The two links shown in purple are best if done with insulated wire as they pass over other pads.
  • Two wires need to be connected to pads directly below the submodules. See the diagram for details.
Modifications required on the rear of the CGS101 VER1.0 PCB. Click through for an enlarged version.
Wiring the DCSM. Note the two wires that run under the PCB. See the modifications diagram above for further details.

There may be some confusion regarding the panel layout and marking of this module. There are two input channels, and two output channels. The input channels are called Channel 1 (on the left) and Channel 2 (on the right). Above them are the two output channels, each with an auxiliary input and a pair of outputs, with the left channel to the left, and the right channel to the right.

Take care not to confuse Channel 1 with the Left output channel, or Channel 2 with the Right output channel.

Pad ID Function
CV Aux in, Left output channel
RV Signal in, Channel 1
RP Gain CV for Channel 1
NP Wiper of pan pot of Channel 1
GP Pan CV of Channel 1
SP Wiper of gain pot, Channel 1
KV Aux in, Right output channel
SV Signal in, Channel 2
BP Gain CV for Channel 2
EP Pan CV of Channel 2
FP Wiper of pan pot of Channel 2
CP Wiper of gain pot, Channel 2
FJ Right output jacks
BN Left output jacks
LK Link these two pads
PV Additional aux in, Left output channel
GV Additional aux in, Right output channel
W 0V power connection (connected to pots etc. as needed)
X +12V power connection (connected to pots etc. as needed)

Setup

There should be no setup required, other than to set the trimmers on the CGS108 PCBs as described on that page.

Parts list

This is a guide only. Parts needed will vary with individual constructor's needs.

Part Quantity Resistors (1% metal film)
330R 8
5.6k 4
82k 4
100k 37
RPD. Use 100k 6
220k 4
100k lin pot 4
Capacitors
82pF ceramic 4
220nF (=0.22uF) 4
10uF 25Velectrolytic 2
Semi's
TL074 1
Misc
Ferrite bead 2
MTA-156 connector 4 pin 1
MTA-156 header 4 pin 1
CGS108 submodule 4
CGS102 submodule set 2
CGS101 VER1.0 PCB set 1

Notes

  • While 100k linear pots have been specified, 50k pots will also work in this circuit.
  • 330R refers to 330 Ohms. 100 nF = 0.1 uF.
  • The module will work on +/-12 volts or +/-15 volts.
  • PCB 6" x 2" with 3mm mounting holes 0.15" in from the edges.

See also

References

External links

Suppliers