CGS combo ETI 447 audio phaser and shifty phase adaptor: Difference between revisions
(Created page with "left|192px| thumb|right|102px| File:cgs_phaser.gif|thumb|right|100px|Click through for 200 DPI B&W printable pane...") |
m (Text replacement - " (archived) by Ken Stone, 1999, with permission of the author" to " by Ken Stone, 1999, with permission of the author - archived") |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[File:cgs panel phaser.gif|thumb|left|102px|Panel artwork. Click through for larger version. Print at 200 DPI.]] |
|||
[[File:cgs_photo_phaser.jpg|left|192px|]] [[File:cgs_panel_phaser.gif|thumb|right|102px|]] |
|||
[[File: |
[[File:cgs photo phaser.jpg|224px|thumb|right|]] |
||
While not really designed for use as a synthesizer module, it was much more convenient for me to mount this unit in the synthesizer rack than having it kicking around on the floor as an effects box. |
|||
The '''CGS phaser''' is the [[ETI]] 447 phaser in combination with a stereo phase adapter. Originally built in the seventies, the unit has spent a number of years kicking around in the junk box built into a "Memory Man" effects pedal box, only recently being rebuilt and modified to improve its performance. All IC sockets were removed, as these had all gone intermittent, and a new batch of 741 |
The '''CGS combo ETI 447 audio phaser and shifty phase adaptor''' is the [[ETI]] 447 audio phaser in combination with a stereo phase adapter. Originally built in the seventies, the unit has spent a number of years kicking around in the junk box built into a "Memory Man" effects pedal box, only recently being rebuilt and modified to improve its performance. All IC sockets were removed, as these had all gone intermittent, and a new batch of [[741]]s soldered in. 741s may not be the best choice for low noise, but I had them to hand, and that is what the original design used. |
||
== Modifications == |
== Modifications == |
||
Component identifiers given below refer to the original |
Component identifiers given below refer to the original ETI Australia schematic. |
||
A 1 meg pot was used for the speed pot (RV2) instead of a 2 meg, because I had this to hand. The capacitors controlling the speed of the LFO (C12 & C13) were reduced from 10 mfd to 4.7 mfd, and the resistor (R28) in series with the speed pot reduced from 100k to 47k. This made the range of speeds more suitable for my needs. |
A 1 meg pot was used for the speed pot (RV2) instead of a 2 meg, because I had this to hand. The capacitors controlling the speed of the LFO (C12 & C13) were reduced from 10 mfd to 4.7 mfd, and the resistor (R28) in series with the speed pot reduced from 100k to 47k. This made the range of speeds more suitable for my needs. |
||
| Line 12: | Line 11: | ||
A depth pot was also added. A 500k pot was hung between the output of the LFO (Pin 6 IC7) and the reference "earth" (+ve of 100 mfd C4). The 1M resistor (R22) was connected to the wiper of this pot instead of directly to Pin 6 of IC7. |
A depth pot was also added. A 500k pot was hung between the output of the LFO (Pin 6 IC7) and the reference "earth" (+ve of 100 mfd C4). The 1M resistor (R22) was connected to the wiper of this pot instead of directly to Pin 6 of IC7. |
||
The design for the stereo phase adapter was taken from an |
The design for the stereo phase adapter was taken from an ETI ''Ideas for Experimenters'' article. This was also built about 20 years ago, using a couple of transistors taken from a (huge!) transistorised calculator. All parts were jammed onto a piece of perf board that was one inch by three quarters. |
||
== CC-BY-NC == |
|||
Readers are permitted to construct these circuits for their own personal use only. Ken Stone retains all rights to his work. |
|||
== See also == |
== See also == |
||
| Line 19: | Line 21: | ||
== References == |
== References == |
||
* ''[https://web.archive.org/web/ |
* ''[https://web.archive.org/web/20180209234737f/http://www.CGS.synth.net:80/modules/phaser.html Phaser]'' by Ken Stone, 1999, with permission of the author - archived |
||
== External links == |
== External links == |
||
* [http://www.synthdiy.com/files/2004/eti447.pdf Project 447 Audio phaser and Shifty phase adaptor], ETI |
* [http://www.synthdiy.com/files/2004/eti447.pdf Project 447 Audio phaser and Shifty phase adaptor], ETI Austalia September 1976, pp. 51-54 and ETI Austalia April 1978 p.99 |
||
* [http://groups.yahoo.com/group/cgs_synth CGS Synth discussion group], for discussion of locating parts, modifications and corrections etc. |
* [http://groups.yahoo.com/group/cgs_synth CGS Synth discussion group], for discussion of locating parts, modifications and corrections etc. |
||
[[Category:CGS |
[[Category:CGS modules from other sources]] |
||
Latest revision as of 18:41, 19 July 2022
The CGS combo ETI 447 audio phaser and shifty phase adaptor is the ETI 447 audio phaser in combination with a stereo phase adapter. Originally built in the seventies, the unit has spent a number of years kicking around in the junk box built into a "Memory Man" effects pedal box, only recently being rebuilt and modified to improve its performance. All IC sockets were removed, as these had all gone intermittent, and a new batch of 741s soldered in. 741s may not be the best choice for low noise, but I had them to hand, and that is what the original design used.
Modifications
Component identifiers given below refer to the original ETI Australia schematic.
A 1 meg pot was used for the speed pot (RV2) instead of a 2 meg, because I had this to hand. The capacitors controlling the speed of the LFO (C12 & C13) were reduced from 10 mfd to 4.7 mfd, and the resistor (R28) in series with the speed pot reduced from 100k to 47k. This made the range of speeds more suitable for my needs.
A depth pot was also added. A 500k pot was hung between the output of the LFO (Pin 6 IC7) and the reference "earth" (+ve of 100 mfd C4). The 1M resistor (R22) was connected to the wiper of this pot instead of directly to Pin 6 of IC7.
The design for the stereo phase adapter was taken from an ETI Ideas for Experimenters article. This was also built about 20 years ago, using a couple of transistors taken from a (huge!) transistorised calculator. All parts were jammed onto a piece of perf board that was one inch by three quarters.
CC-BY-NC
Readers are permitted to construct these circuits for their own personal use only. Ken Stone retains all rights to his work.
See also
References
- Phaser by Ken Stone, 1999, with permission of the author - archived
External links
- Project 447 Audio phaser and Shifty phase adaptor, ETI Austalia September 1976, pp. 51-54 and ETI Austalia April 1978 p.99
- CGS Synth discussion group, for discussion of locating parts, modifications and corrections etc.