Heat shrink tubing: Difference between revisions
m (Text replace - "|frame|" to "|thumb|") |
No edit summary |
||
(2 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
[[File:Schrumpfschlauch animated modified.gif|thumb|Animation of heat shrink tube before and after heating |
[[File:Schrumpfschlauch animated modified.gif|thumb|Animation of heat shrink tube before and after heating.]]'''Heat shrink tubing''' is useful for electrical insulation, color coding, cable bundling and mechanical protection. For electronics 1 mm (1/16") fits component leads and will shrink to a skin tight fit. Otherwise the 1/8" and 1/4" diameter sizes are often useful.<ref name="jr">[http://www.justradios.com/heatshrinktubing.html '''Heat Shrink Tubing'''], JustRadios.com</ref> It is also available with adhesive inside. |
||
==Uses== |
== Uses == |
||
To |
To form a thermally insulating sleeve over the transistor pair and [[tempco]] in an [[exponential converter]]. Strain relief on exposed connections, e.g. leads soldered on [[potentiometer]] tags. To terminate the insulation, e.g. after the screen has been separated from the core wires and sleeved. Especially to sheath and insulate all exposed mains connections, e.g. the solder connections on a front panel mains on/off switch. |
||
==Method== |
== Method == |
||
Normally a heat gun is used to shrink the sleeving, taking care not to damage nearby areas and to not overheat the sleeving. The heat from a soldering iron can be used, without touching the sleeving. Do not use a direct flame. A hair dryer won't be hot enough. |
Normally a heat gun is used to shrink the sleeving, taking care not to damage nearby areas and to not overheat the sleeving. The heat from a soldering iron can be used, without touching the sleeving. Do not use a direct flame. A hair dryer won't be hot enough. |
||
==Shrink ratio== |
== Shrink ratio == |
||
The shrink ratio is the approximate maximum amount the heat shrink tubing will fully shrink compared to its unshrunk diameter. For example, a 3/4" piece with a 3:1 shrink ratio will shrink down to a maximum diameter of approximately 1/4”. Tubing with a larger shrink ratio is more forgiving in fitting, and has a bit thicker wall thickness and slightly less flexibility when shrunk than a lower ratio product.<ref>[http://www.techflex.com/howtos/heatshrink.pdf How to work with heatshrink tubing...], Techflex How-Guide</ref> |
The shrink ratio is the approximate maximum amount the heat shrink tubing will fully shrink compared to its unshrunk diameter. For example, a 3/4" piece with a 3:1 shrink ratio will shrink down to a maximum diameter of approximately 1/4”. Tubing with a larger shrink ratio is more forgiving in fitting, and has a bit thicker wall thickness and slightly less flexibility when shrunk than a lower ratio product.<ref>[http://www.techflex.com/howtos/heatshrink.pdf How to work with heatshrink tubing...], Techflex How-Guide</ref> |
||
==Useful sizes== |
== Useful sizes == |
||
To provide a degree of mechanical support for connections, e.g. to switches and jacks, a |
To provide a degree of mechanical support for connections, e.g. to switches and jacks, a 1 cm length of 2.4mm heat-shrink will be fine for the the majority of wiring connections. For larger cables like power leads, use 6.4mm. Otherwise a small kit with short lengths of different diameter should cover. |
||
==References== |
== References == |
||
{{reflist}} |
{{reflist}} |
||
==External links== |
== External links == |
||
*[http://www.doityourself.com/stry/7-different-sizes-of-heat-shrink-tubing 7 Different Sizes of Heat Shrink Tubing] |
* [http://www.doityourself.com/stry/7-different-sizes-of-heat-shrink-tubing 7 Different Sizes of Heat Shrink Tubing] |
||
*Wikipedia: [https://en.wikipedia.org/wiki/Heat-shrink_tubing Heat-shrink tubing] |
* Wikipedia: [https://en.wikipedia.org/wiki/Heat-shrink_tubing Heat-shrink tubing] |
||
[[Category:Wiring]] |
[[Category:Wiring]] |
Latest revision as of 10:08, 9 July 2022
Heat shrink tubing is useful for electrical insulation, color coding, cable bundling and mechanical protection. For electronics 1 mm (1/16") fits component leads and will shrink to a skin tight fit. Otherwise the 1/8" and 1/4" diameter sizes are often useful.[1] It is also available with adhesive inside.
Uses
To form a thermally insulating sleeve over the transistor pair and tempco in an exponential converter. Strain relief on exposed connections, e.g. leads soldered on potentiometer tags. To terminate the insulation, e.g. after the screen has been separated from the core wires and sleeved. Especially to sheath and insulate all exposed mains connections, e.g. the solder connections on a front panel mains on/off switch.
Method
Normally a heat gun is used to shrink the sleeving, taking care not to damage nearby areas and to not overheat the sleeving. The heat from a soldering iron can be used, without touching the sleeving. Do not use a direct flame. A hair dryer won't be hot enough.
Shrink ratio
The shrink ratio is the approximate maximum amount the heat shrink tubing will fully shrink compared to its unshrunk diameter. For example, a 3/4" piece with a 3:1 shrink ratio will shrink down to a maximum diameter of approximately 1/4”. Tubing with a larger shrink ratio is more forgiving in fitting, and has a bit thicker wall thickness and slightly less flexibility when shrunk than a lower ratio product.[2]
Useful sizes
To provide a degree of mechanical support for connections, e.g. to switches and jacks, a 1 cm length of 2.4mm heat-shrink will be fine for the the majority of wiring connections. For larger cables like power leads, use 6.4mm. Otherwise a small kit with short lengths of different diameter should cover.
References
- ^ Heat Shrink Tubing, JustRadios.com
- ^ How to work with heatshrink tubing..., Techflex How-Guide