MU parts
This information is for doing DIY, repaneling, and/or repairs on MU systems. It's not comprehensive, everyone has preferences, but lists the common/major/most-wanted parts in the MU format, and/or what sort of things will work.
Panels/Faceplates
Specifications
See synthesizers.com:Panels
Blank panels
Blank panels can be purchased from:
- Moon Modular, 1 and 2U
- STG Soundlabs, 1U
- Synthesizers.com, 1, 2, 4, and 8U
Project panels
Panels for specific projects (CGS, YuSynth, etc.) can be purchased from:
Custom panels
Custom panels can be manufactured by:
- Big Blue Wave
- Front Panel Express, USA
- Schaeffer, EU
For FPE and Schaeffer, you need to supply the blank MU panel.
Panel parts
Knobs
Dotcom (Synthesizers.com) use fluted dual-dot 1" Moog-style/Cosmo Corporation knobs, available at:
For pointer knobs, Dotcom use 1.125" Moog-style/Cosmo Corporation skirted pointer knobs, available at:
Potentiometers
Synthesizers.com use Alpha single-gang 24mm pots, available at:
- Mouser 100K linear 31VA501-F and 100K log 31VJ501-F
- Small Bear Electronics
- Synthesizers.com 100K, 1M
Switches
..., available at:
- Synthesizers.com DPDT, SPDT
Pushbuttons
..., available at:
Jacks
Dotcom modules use enclosed mono Switchcraft-style jacks, available at:
Switched 1/4" jacks are especially handy for Normalising jack connections.
LEDs
... Panel components sold by Synthesizers.com come with 6" wires and MTA connector.
PCB Mounting
Synthesizers.com and some independent manufacturers mount the PCB parallel to the panel with standoffs, others mount PCBs perpendicular MOTM-style. 4-40 steel mounting brackets are fine for this and also work with CGS boards.
PCBs can be mounted parallel using 1" (Mouser: 534-8405) and 1.25" (Mouser: 534-8407) threaded standoff posts. Black oxide screws, like the ones used by Synthesizers.com, are used to affix the standoffs to the front panel. Specifically, 4-40 steel 3/8" black oxide phillips pan head screws,[1] are available from Aaron's Machine Screws.
For perpendicular mounting with stooge brackets affixed by the pots or jacks, available at:
Threaded right-angle brackets (Mouser: 534-621) can be mounted to the panel, using the 4-40 steel 3/8" black oxide phillips pan head screws.[1]
Internal connectors
Dotcom uses MTA-100 connectors, using 24 awg wire. To fit the wires to the connectors, use the AMP MTA key style maintenance tool: AMP 59803-1 (DigiKey: A9982-ND).
Module power
Power supplies are connected using 6-pin keyed MTA-100 connectors.[2]
| pin | Voltage |
|---|---|
| 1 | +15 (white) |
| 2 | key - pin missing and plugged |
| 3 | +5 (red) |
| 4 | GND (black) |
| 5 | -15 (green) |
- Female cable mount: AMP 6404416 (Mouser: 571-3-640441-6)
- Male PCB mount: AMP 6404566 (Mouser: 571-6404566)
Panel connectors
2-pin MTA-100 connectors are used to connect jacks, push-buttons, and LEDs.
| pin | Connection |
|---|---|
| 1 | Signal (tip) |
| 2 | Ground (sleeve) |
- Female cable mount: AMP 6404412 (Mouser: 571-3-640441-2)
- Male PCB mount: AMP 6404562 (Mouser: 571-6404562)
3-pin MTA-100 connectors are used for switches and pots.[3]
| pin | Connection |
|---|---|
| 1 | CCW side |
| 2 | Wiper |
| 3 | CW side |
CCW means the low (Counter Clockwise) terminal and CW the high terminal.
- Female cable mount: AMP 6404413 (Mouser: 571-3-640441-3)
- Male PCB mount: AMP 6404563 (Mouser: 571-6404563)
References
- ^ a b Guitar Fool:Hardware
- ^ Internal DC Module Power - 6 pin MTA
- ^ www.synthesizers.com:Internal Pot/Switch - 3 pin MTA
- The 5U DIY Resource Wiki, Muff Wiggler forum
External links
- Synthesizers.com:Technical information