Rob Hordijk Dual Phaser

Contact Rob directly for details about his modules: rhordijk@xs4all.nl.

Rob also has a subforum at the Electro-Music forum site: http://electro-music.com/forum/index.php?f=185

Most of Rob's module designs use SSM quad VCA chips, possibly the Analog Devices SSM2164 (?)

OSC HRM
Price 325 euro The Harmonic Oscillator module (OSC HRM) is used to create pitched waveforms with dynamically controlled timbres. Pitch control law is 1V/Oct and the module uses a platinum element for temperature stabilization of the pitch curve. Maximum frequency range is from 0.5 Hz to 16.000 Hz and the scale is perfectly tuned in the middle six octaves up to a pitch of 4.000 Hz. When playing pitches higher as 4000 Hz the 1V/Oct scale starts to break down, due to the necessary internal bandlimiting in the harmonic generators. The module uses a biquad sine/cosine oscillator at its core and through a process of recursion harmonic series of overtones are generated. There are two recursion paths, one that produces all harmonics and one that produces only the odd harmonics. By gradually opening the knobs that control the amount of recursion more and more harmonics are generated. When only the all harmonics path is used the waveform morphs smoothly from a sinewave to a waveform that closely resembles and sounds like a sawtooth or an inverted sawtooth. Opening only the odd harmonics knob will smoothly morph from a sinewave to a squarewave. When opening both knobs effects like pulse wave modulation are possible. Building up these harmonic series is under full voltage control and can be modulated from slow LFO speeds to fast audio rates to create FM timbres. When the waveforms are modulated there is a negligable amount of detune (less than 1 cent), though when modulating at audio rates an asymmetry in the modulating waveform can cause detune effects on deep modulations. There is an additional VCA incorporated in the module. The final output signal can be taken from a point just before the VCA and at the output of the VCA. This enables the module to be easily used in a situation where one wants to modulate another module by an audio rate signal and have the modulation depth under voltage control using e.g. a LFO waveform, an envelope voltage signal or a play controller that produces a control voltage, while still having the full output level signal available on the full output to serve different purposes. The waveforms have an exceptionally warm sound and when dynamically modulated have a deep spatial and organic character. With only one OSC HRM and one DUAL ENV module you can already have a voice with dynamic timbral and volume control that can do e.g. a pretty solid bass line

Dual Phaser
Price: 385 Euro.

The internal CV voltage scale is 1V/Oct. Each phaser has a reasonably accurate one volt per octave direct control input that can track the keyboard voltage. Normalization is used, routing the V/Oct input signal of phaser1 into phaser2 when the phaser2 V/Oct input is left unplugged.

Total control range is about 18 octaves. The Frq knob goes over the top 9 octaves of this range. Through the V/Oct and Modulation inputs you can go deeper, but you get into the LFO range and audible phasing effects would disappear.

It is however possible to use the phasing effect on LFO control signals in the 1Hz to 10Hz range by supplying the V/Oct with e.g. a fixed -5V control signal, which can create quite interesting LFO effects on e.g. drones. All inputs and outputs are DC coupled, so CV signals can pass the module equally well as audio signals. Only the internal resonance is AC coupled, so resonance drops off below roughly 10Hz.

Additionally each phaser has a modulation input, also at 1V/Oct when the mode is set to sweep. When the mode is set to spread it behaves like the modulation sensitivity is halved, also when it is in half mode where only half of the poles in each phaser are modulated by this input. These inputs are not normalized, in fact if no plug is connected the modulation level knobs receive a fixed voltage so a manual spread value can be set.

Audio input is maximum 12V peak/peak before clipping occurs and there is 6dB attenuation from input to output to enable resonance peaks without clipping.

Audio routing is as follows: If a jack is connected to input1, and if input2 is unconnected, then the audio will route into both phasers. In this mode you can use the two phaser outputs as a stereo signal. Connecting a jack to input2 will override this internal input1->input2 connection and separate both phasers.

If audio is routed into input1 and if input2 is left unconnected, and if a jack is connected into ónly output2, then the two phasers are automatically set to "inverse parallel" mode. Meaning that if both phasers are set to exactly the same knob settings the phaser outputs would be in exact reverse phase and thus result in almost silence.

If audio is routed into input1, and if output1 is connected with a short cable to input2, and if output2 is taken as the overall output, the two phasers are in series and thus result in one 16-pole phaser.

To summarize: you can use the phasers fully separated, parallel with two (stereo) outputs on one input signal, parallel with mono output but with one phaser in reversed phase before the mixing of the outputs of the phasers take place on output2, or in series. All this is accomplished by the internal switches in the connectors and only depends on which inputs and outputs have a plug."

Active Matrix
Price: a little under 500 Euro.
The Active Matrix module is buffered and works similar to the EMS Synthi. It comes with mono plugs and some have built-in resistors for -6db or -12db signal reduction. Every point is an insert, and with an insert cable, you can patch whatever you like into that point.

Dual Envelope Generator