CGS Serge ring modulator
CGS79 the CGS Serge ring modulator module is a variation on the 1973 Classic Serge R6 Ring Modulator.
From the catalog (abridged): The RING MODULATOR (MOD) is an AC or DC coupled Ring Modulator featuring superior audio processing capabilities. The Ring Modulator offers two VC inputs in addition to the two signal inputs which may be used to perform voltage controlled transitions between full ring modulation and amplitude modulation.
The module will work on +/-12 volts or +/-15 volts.
A little on how it works
Before you start assembly, check the board for etching faults. Look for any shorts between tracks, or open circuits due to over etching. Take this opportunity to sand the edges of the board if needed, removing any splinters or rough edges.
When you are happy with the printed circuit board, construction can proceed as normal, starting with the resistors and diodes first, followed by the taller components.
Take particular care with the orientation of the polarized components, such as electrolytics, diodes, ICs and transistors.
If you are planning to use it with 6.3mm or 3.5mm jacks, the common of these jacks should be wired to 0V/GND as usual. Just solder the return wire to the (unused) center pins of the power connector.
Transistor types are not critical. BC557 has been substituted for the original types used. 2N3906 can be used if installed backwards with respect to the outline on the overlay.
There are three sets of pads for 1206 100n capacitors on the rear of the PCB. The one near the LM31700 is only needed if that chip is used. The other two are optional.
If you are unable to purchase CA3080 or LM3080 variants, there is provision on the PCB for a LM13700/LM13600 variant to be used in its place. The 1k resistor next to this chip is only required if this type of chip is used, otherwise leave both the chip location and resistor location empty. Do not install chips in both the LM3080 and LM13600 locations. See the following note if you are using a LM13700/LM13600:
Ver 1.0 corrections
Notes for the Ring Modulator
As this is a dual purpose PCB, there are some variations between the build types. The Ring Modulator specific components and values start with "R". Do not use any value staring with "G". The PCB stuffing diagram above has been modified to show all the parts required on the Ring Modulator. Install all parts as shown.
Preliminary adjustments - Adjust the panel potentiometer all the way to ground (CW). Adjust TR3 to center position Adjust TR2 fully to +V position Input 500 Hz 0/5V sawtooth into Input X AND pad A (no panel connection) While looking at the output, adjust TR1 until the output waveform is perfectly symmetrical (and rectified), as below.
Now disconnect the sawtooth from Input X (keeping it connected to pad A). Turn the scope sensitivity up. Adjust TR3 until the least feed through of the sawtooth is seen (or heard).
It would be good to repeat the initial adjustment of TR1 as above, mow that TR3 has been set.
Finally, with the sawtooth still connected to Input X, connect it to Input Y. Now adjust TR2 to achieve as symmetrical an output at 1000 Hz as possible. Note that the waveform will be somewhat different to the previous one, due to the non linear characteristic of the transistor pair.
Set X-XY pot to X (CCW).
Connect an audio frequency triangle wave to X input.
Adjust trimmers TR2 and TR3 for minimum breakthrough. This will require alternately adjusting the two trimmers until you get the desired result.
Move the audio frequency triangle wave to the Y input.
Connect a second triangle wave, this time at around 1Hz, to the X input.
Adjust TR1 for a balanced "throb".
This is a guide only. Parts needed will vary with individual constructor's needs.
|Resistors (1% metal film)|
|25k lin pot||1|
|100nF 1206 SMT (=0.1uF) see text.||3|
|MTA-156 header 4 pin||1|
- A TL071 or similar can be used in place of the LM307.
- 330R refers to 330 Ohms. 100 nF = 0.1 uF.
- PCB 6" x 1" with 3mm mounting holes 0.15" in from the edges.
Readers are permitted to construct these circuits for their own personal use only. Ken Stone retains all rights to his work. Serge Tcherepnin retains all rights to his work.
- Ring Modulator for music synthesizers. (archived) by Ken Stone, 2013, with permission of the author
- Info on the original Serge module
- Original Serge kit assembly and set-up instructions
- CGS79RING v1.1 BOM at BOMpiler
- CGS Synth discussion group, for discussion of locating parts, modifications and corrections etc.
- CGS79 Ring Modulator, revision 1, Elby Designs