Panel (homebrew): Difference between revisions

Jump to navigation Jump to search
Content added Content deleted
VisualWikitext
Line 73: Line 73:
* [http://www.mcmaster.com/#standard-aluminum-sheets/=xe70s0 About Aluminum], McMaster-Carr
* [http://www.mcmaster.com/#standard-aluminum-sheets/=xe70s0 About Aluminum], McMaster-Carr
=== Designs ===
=== Designs ===
* [http://modularsynthesis.com/modules/parts/parts.htm FrontPanelExpress Templates] by David Brown, ModularSynthesis.com
* [http://modularsynthesis.com/modules/parts/parts.htm Front Panel Express Templates] by David Brown, ModularSynthesis.com
* [https://groups.yahoo.com/neo/groups/ModularSynthPanels/files Modular Synth Panels] files, Yahoo group
* [https://groups.yahoo.com/neo/groups/ModularSynthPanels/files Modular Synth Panels] files, Yahoo group
* [http://pugix.com/synth/?s=fpd fpd files] by Richard Brewster
* [http://pugix.com/synth/?s=fpd fpd files] by Richard Brewster

=== Finishing ===
=== Finishing ===
* [http://syinsi.com/finishing-aluminum-panels/ Finishing Aluminum Panels], syinsi.com
* [http://syinsi.com/finishing-aluminum-panels/ Finishing Aluminum Panels], syinsi.com

Revision as of 19:08, 6 September 2016

Moog 921, 911 and 902 modules, with visible component mounting screws.

The panel, front panel or faceplate is where most or all of the controls and displays are mounted. Usually it is the primary user interface for patching, control and operating besides actually playing notes.[1]

Aesthetics

Fabricating attractive front panels for a synthesizer can be a real challenge. Great care should go into creating an attractive synthesizer. The quality of work put into a guitar build, chrome fittings, pearl inlays, exotic woods all help inspire the musician and so it should be with the synthesizer. The design of a good-looking system requires much time spent mentally going over the various relationships of the modules and how the instrument will be used.[2]

Layout

Having elements too close together can introduce noise and crosstalk, spaciousness helps towards reducing unwanted problems. Choose between having jacks easier to read placed near their associated controls, [3] or below where patch cables are then easier to keep out of the way.

Design the panel so that behind the panel the potentiometer and jack bodies have enough clearance from each other and that in front both the controls and the users fingers have enough room to operate. Also check that any parts close to an edge won't interfere with mounting the panel into its enclosure. Check the angle of rotation of the pot will match the scale going to be marked on the panel.[4] Components laid out on a grid can use a half grid distance from their edge on adjacent panels.

Modular synthesizer panels

With a modular synthesizer module the front panel is also a structural element. Except for the power supply and power rails, the rest of the synth module internals are supported by the panel. Panels are usually made of thicker aluminum or have flanges to give extra stiffness, for example to withstand the forces of plugs being inserted and removed from the jacks. The PCB when attached parallel to the panel can be done by mounting pillars or via the pots and jacks soldered to the PCB, but check how this might strain the the solder joints. When attached perpendicularly the PCB is held in place usually with a stooge bracket and fastened against the panel by the pots and jacks, or simple 4-40 steel mounting brackets.[1][2]

Material

Usually aluminium; T3 or T6 6061 1.59mm (0.0625") aluminium sheet. This is easy to machine and isn't too soft. Sometimes other materials are used such as some sheet metal, acrylic (aka Lucite or Perspex), glass-reinforced epoxy laminate (FR4 PCB), plywood or formica.[5][6][7]

Drilling

A unibit aka step drill bit.

Use a center punch to mark the panel for drilling. This will stop the drill bit from wandering. First drill a pilot hole, then use increasingly larger size drill bits until the correct hole diameter is reached.[5] However it's more efficient to use a unibit aka step drill bit.[4] Also check for correct mounting against the data sheet, e.g. hole dimensions and maximum panel thickness.[3]

Labelling

Controls for particular functions can be grouped together by panel graphics. Individual controls labels can be with text and others with graphics. Scales can be indicated with tick marks. Signal routing can be indicated. Besides writing or painting directly on the panel by hand, there are a number of different methods to add labelling. Traffolyte laminate or Dymo embossed labels were once common. Adhesive labels tend to fall off after a while. Laser printed graphics are common now, as well as a variety of iron-on transfer methods.[1]

Note that for the methods listed here panels can be given a protective coating of clear lacquer after labelling.[8]

CNC engraving

Requires a large investment to produce panel drilling approaching commercial quality.[9] It's more efficient to use a drill press for making holes and use CNC for engraving. Engravings in anodised aluminum panel can be blackened with Birchwood Casey Aluminum Black[10] or coloured using a Markal Lacquer-Stik.[11][8]

Etched

With chemical etching using Press and Peel transfer film, toner transfer or lacquer, masking areas of the panel from the etchant.[12] A variety of etchants can be used, taking into consideration what type of metals is used for the panel. This can be hazardous, so some care is needed in dealing with whatever chemicals are used as well as with the process itself. Safer methods are described at Non-toxic method for etching copper and brass.[11]

Laminated

The panel overlay is laminated in a plastic pouch, which is attached to the panel with contact adhesive. Print two copies of the overlay and use one of them as a drilling guide. Laminate pouches are also available in different finishes which you might be preferable. A problem with this method is that with the edges catching on other panels the platic laminate might lift at the corners.[4][5]

Laser

Anodized aluminum can be laser etched.

Paint infilling

Acid etched or engraved panels can be infilled with Revell enamel model or automotive touch up paint and the excess paint cleaned up after it's cured.[11][8]

Paint stick

Similar to paint infilling but easier. Using a Markal Lacquer-Stik.[11][8]

Painted

MOTM panels finish is baked-on two part Polane paint,[13] giving it a crinkly look, and with labeling and scales in silk screen printed epoxy-ink.[14]

Printed paper

A laser print is made, of the same size as the panel and then glued onto it.

Screen printed aka silk screen

...

Toner transfer

...

See also

References

  1. ^ a b c Front panel, Electronic Music Wiki
  2. ^ a b Build a Better Music Synthesizer by Thomas Henry, Tab Books, 1987, ISBN 0830602550
  3. ^ a b Electro-music.com forum:Standard measurements in front panels
  4. ^ a b c How i make front panels.
  5. ^ a b c How To Make Synth Panels by Ray Wilson, MFOS
  6. ^ What type of aluminium is used for faceplates?, Muff Wiggler forum, June 2013
  7. ^ Aluminum Panel Guage???, Muff Wiggler forum, January 2012
  8. ^ a b c d Infilling DIY engraved panels?, Muff Wiggler forum, Feb. 2012
  9. ^ Anybody using a Fireball CNC router to make panels/ pcb ?, Muff Wiggler forum, April 2012
  10. ^ DIY CNC milling/labelling of steel panels, Muff Wiggler forum, Aug 2012
  11. ^ a b c d Tips & Tricks, Engravers Solutions
  12. ^ How I Do Etching, DIY Guitar Effects
  13. ^ Where to get MOTM-style silkscreened panels made?, Muff Wiggler forum, May 2012
  14. ^ MOTM Info

External links

Designs

Finishing

Etching

Outsourcing

Retrieved from "https://sdiy.info/wiki/Panel_(homebrew)?oldid=7134"