...and similarly for decreases). This can be considered to be like a rounding error that gets injected, as noise, into the input stream as a consequence of con
...
10 KB (1,564 words) - 12:12, 11 June 2022
...rs I cannot be certain if this was a constructor error, or a panel marking error.
...
2 KB (300 words) - 14:50, 19 July 2022
...rect the problem. Note that the currently available PCB does NOT have this error, and needs no modification.
...
10 KB (1,761 words) - 14:50, 19 July 2022
...e tube for both grounded grid amps. It may have even been down to a wiring error, or the decoupling capacitor I used being too small.
...of which is fed into the CV input mixer to allow correction of any tuning error introduced by the capacitors. The capacitor values are not critical. They w
...
4 KB (756 words) - 18:41, 19 July 2022
...1: Has 8 pin "dip switch" location near ROM. Very small pads. Has the 2532 error.
* Version 2: Has NO "dip switch" location near ROM. Has the 2532 error.
...
12 KB (2,094 words) - 18:41, 19 July 2022
...enter|600px|The component overlay for the v2.0 PCB. Due to a manufacturing error, the overlay on these PCBs has a few labels obscured by extra text. Print o
An error has been found on the v2.1 PCB. In the Lockhart multiplier the end of the 1
...
16 KB (2,722 words) - 18:53, 19 July 2022
Due to a manufacturing error, the overlay on one version of these PCBs has become cluttered. Print out t
...
9 KB (1,617 words) - 18:42, 19 July 2022
...ith less than one [https://en.wikipedia.org/wiki/Cent_(music) cent] tuning error.<ref name="dsheet">[http://www.soundsemiconductor.com/downloads/ssi2131data
...
1 KB (153 words) - 09:49, 10 June 2022
'''CGSMULT''' the '''CGS multiple''' circuit board provides an easy and error-free way of wiring up a banana jack multiple.
...
2 KB (317 words) - 18:43, 19 July 2022
...ment, and it has a voltage controlled resonance path added. There'a little error in the drawing: the pnp current mirrors have C and E mixed up.
...
8 KB (1,132 words) - 22:24, 27 June 2024
On the VER1.0 PCB there is an error with the pot pads. The inner CW pad is not connected to the outer CW pad. I
...
4 KB (796 words) - 18:43, 19 July 2022
'''Please note that there is an error in the documentation and PCB for this project. The resistor marked 180k (R2
...
12 KB (2,133 words) - 17:28, 15 February 2023
[[File:cgs_lpg_error.gif|thumb|center|800px|There is an error on the rear of the PCB. This can be corrected by making two cuts in one tra
...
11 KB (1,835 words) - 18:45, 19 July 2022
...nt depending on personal requirements. '''Note that due to a manufacturing error, one of the PWM input pads is not connected to it's resistor. The missing t
...
16 KB (2,744 words) - 14:50, 19 July 2022
...e increased, to as much as 33k, dependent on the individual LED. Trial and error is the only way to correctly determine the value. This can be done with a L
...
7 KB (1,136 words) - 18:45, 19 July 2022
There is an error on this board at the output buffer op-amp (TL071). A trace goes to pin 5. T
...
4 KB (590 words) - 18:48, 15 February 2023
{{font color|red|Important:}} The first run of PCBs has a minor error - the voltage follower IC4B (center bottom of the PCB) has its wiring confu
...
9 KB (1,446 words) - 19:50, 15 February 2023
Due to a manufacturing error, the overlay on one version of these PCBs has become cluttered. Print out t
...
6 KB (986 words) - 14:50, 19 July 2022
Due to a manufacturing error, the overlay on these PCBs has become cluttered. Print out the above file t
...
9 KB (1,467 words) - 18:54, 19 July 2022
...or an enlarged, printable version. Print at 300dpi. Due to a manufacturing error, the overlay on one version of these PCBs has become cluttered. Print this
...
8 KB (1,389 words) - 14:50, 19 July 2022