|{{Background color|brown| }} {{Background color|green| }} {{Background color|gold| }}||1R5
|{{Background color|green| }} {{Background color|brown| }} {{Backgrou
...
24 KB (3,311 words) - 23:13, 26 March 2023
|{{Background color|brown| }} {{Background color|green| }} {{Background color|gold| }}||1R5
|{{Background color|green| }} {{Background color|blue| }} {{Backgroun
...
12 KB (1,723 words) - 23:12, 26 March 2023
...font color|black|white| white }}, {{font color|white|green| green }}, {{font color|white|blue| blue }} and {{font color|black|
...een| green }} or {{font color|white|purple| purple }}||Green is second channel/style of some CV out (e.g. velocity out), purple is third
...
13 KB (1,977 words) - 18:46, 15 February 2023
...e only installed if you have a separate 5V power rail.}}{{font color|green|Green (B) components are only installed if you have only +/-15V power rails.}}]]
...e 5V power rail.}} {{font color|green|Components are only installed in the green (B) area if you have only +/-15V power rails.}} Click through for an enlarg
...
8 KB (1,382 words) - 17:31, 15 February 2023
...ixer. If the 200k resistors, marked in blue on the schematic (and blue and green on the overlay) are replaced with 100k resistors, the result will be a unit
...ors marked in blue would also need to be reduced to 49.9k. The resistor in green on the PCB (for the first stage) would be left as is. An external voltage d
...
7 KB (1,243 words) - 14:50, 19 July 2022
=== ''ANALOG SEEKrets (DC to daylight)'' by Leslie Green ===
...
8 KB (1,140 words) - 18:31, 15 February 2023
...LEDs with resistors in the range of 10k (for red/amber/yellow) to 33k (for green/blue). Using high mcd/super-bright/ultra-bright LEDs reduces the switching
...ing it to the tally for that channel. A different color jack, in this case green, indicate that an input responds negatively, subtracting the input voltage
...
14 KB (2,467 words) - 16:39, 9 April 2024
...ont color|black|orange| orange }},{{font color|white|green| green }}<ref name="animal"/>||
...
7 KB (1,021 words) - 19:41, 15 February 2023
| -330||Green||N330||S2H
| -3300||Green/orange||N3300||—
...
9 KB (964 words) - 13:51, 18 September 2023
...tps://www.taydaelectronics.com/leds/round-leds/3mm-leds/led-3mm-green.html green, 3mm]
...tps://www.taydaelectronics.com/leds/round-leds/5mm-leds/led-5mm-green.html green, 5mm]
...
13 KB (1,643 words) - 18:43, 7 April 2024
...can be determined from the circuit diagram. The earlier board is shown in green, while the Rev 1 board is shown in red.]]
...
15 KB (2,541 words) - 14:50, 19 July 2022
...s in which the dielectric is exposed: one such example is block shaped and green in color will not work.
...
9 KB (1,672 words) - 14:50, 19 July 2022
...le:mountingholes.jpg|thumb|right|250px|middle|The MOTM holes are marked in green and Synthesizers.com in red.]] Mark the holes making sure the module is cen
...
10 KB (1,488 words) - 18:03, 15 February 2023
...s in which the dielectric is exposed: one such example is block shaped and green in color. Another example is shown below. They will not work.
...
10 KB (1,788 words) - 14:50, 19 July 2022
* Green: Lumex SSI-LXH387GD (DigiKey: 67-1156-ND)
...
7 KB (932 words) - 18:35, 15 February 2023
...have used four different colored LEDs for the steps, with beats 1 and 5 in green, 2 and 6 in yellow, 3 and 7 in orange and 4 and 8 in red. This helps give a
...
21 KB (3,706 words) - 14:50, 19 July 2022
|5||-15 (green)
...
8 KB (1,129 words) - 18:09, 15 February 2023
...each stage. They are marked "G" and "H" on the schematic and the PCB. The green/white and brown/white wires connect the first and last stages together]]||[
...
14 KB (2,523 words) - 18:42, 19 July 2022
*<span style="color:#00ff00">Green</span> is a gate signal.
...
924 bytes (145 words) - 18:09, 24 April 2021
...y on the rear of the PCB by cutting the tracks in the areas shown in light green on the diagram below. After some solder mask is scraped from the remaining
...
8 KB (1,309 words) - 18:43, 19 July 2022