Search results

...nly provide Gate signals and voltages responding to pressure being applied to the pads. There are no musically pitched voltages generated. That must be h ...s useful if you wish to use the keyboard (in conjunction with Programmers) to play melodies with touch control of their dynamics. ...

...ing a copy of the original Digisound ROM while the other has been modified to take a 2732 which contains an experimental table I put together. ...the PCB for this module, so not all comments in this article are relevant to all boards.''' ...

...ge to be active at any time, outputting the corresponding control voltages to their bussed output jacks. The stages could be selected either via a gate/t ...stages used as an "introduction", with the sequence automatically looping to a stage in the middle of the panel once the sequence's first run was comple ...

...w me will know I'm not a big VCF fan. Nonetheless, this VCF really appeals to me. Its sound is quite unlike the Moog ladder, has a lot of character. ...oscillating, the resonance pot needs to be backed off a fair way to get it to stop again. It can also be frequency dependent. ...

== How to use this module == ...en connect outputs 1 and 2 to two drum sound generators. A pulse train fed to the clock input would then produce a drum roll alternating between the two ...

...ont panels. It's not comprehensive, everyone has preferences, but attempts to cover the commonly used parts and what sort of things will work. ...ef> Vertical mount front panel components will need to of a similar height to neatly fit the gap between the PCB and front panel. ...

...set the values of the parameters and messages used in Module:Documentation to -- localise it to your wiki and your language. Unless specified otherwise, values given here ...

...ences, trills etc., when used with VCOs. Of course it's use is not limited to VCOs only. ...e" techniques, the CV outputs are constant from the beginning of the cycle to the end - there is no "charge period" in which a brief glide is heard. ...

...ences, trills etc., when used with VCOs. Of course it's use is not limited to VCOs only. ...e" techniques, the CV outputs are constant from the beginning of the cycle to the end - there is no "charge period" in which a brief glide is heard. ...

...and comparators with surprising results, ranging from complex wave shaping to pitch shifting of saw tooth waves. == Some ideas on how to use this module == ...

...soon realized this wasn't going achieve what I wanted. I needed to be able to control when these jumps could occur. As such, some form of memory element ...esultant voltage is fed to a VCO, effects from subtle semi-random melodies to 70s sci-fi computer sounds can be generated. ...

...to [[KiCad PCB EDA Suite|KiCad]] and [[Git]] but who have enough know-how to open a terminal and use the command line. == Contributing to KiCad == ...

...om the original owners manual. Only some parts of this document will apply to any home constructed units. Please note that Metasonix is not available for ...nverter to drive the TS-23, set it to output Hz/V and attach its CV output to either CV input of the TS-23. The TS-23's driver circuit was set so that 0. ...

...nto). Voltages from a keyboard, sequencer, or other sources can be applied to the IN jack, and the RISE and FALL knobs will now determine the rate of gli ...k set by the processing knob. Since both the RISE and FALL can be switched to be controlled separately or together, the slope of either or both can be sh ...

...multiplexor, i.e. ''not bidirectional''. It can route one of eight signals to its output, ''but not the other way around''. It can also provide in depend ...our control input processors. These convert any incoming CV or gate signal to those suitable for the internal circuitry of the module. Their sensing poin ...

...]] and [[Doepfer Musikelektronik GmbH|Doepfer]], with different approaches to module power connectors and front panel mounting holes. These days the Doep ...few tenth of a mm less than whatever multiple of 5.08 mm it is, to give some tolerance for final assembly. A [[19-inch rack]] has a usable wid ...

== Some ideas on how to use this module == ...is a multiplexor, i.e. not bidirectonal. It can route one of eight signals to its output, but not the other way around. It can also provide independant g ...

...cribing the unique sound qualities (there are three different sections) is to say that they alter the timbre in exciting new ways, producing interesting ...re is a rounded flattening of the signal peaks: an effect somewhat similar to overdriving a tube amplifier (except that in this version the process is vo ...

...the module, in the 1/f mode, the size of a pitch step is inversely related to the frequency at which it will occur. In other words, the smallest steps ar ...D/A converter, it drives a bank of knobs, allowing harmonic relationships to be set up. ...

...om the original owners manual. Only some parts of this document will apply to any home constructed units. Please note that Metasonix is not available for ...edance line-level input. Please use the volume control in the amp or mixer to control the listening level. (Headphones are especially useful in understan ...