Eurorack panel components

Jump to navigation Jump to search

This information is for doing DIY, or repairs on Eurorack front panels. It's not comprehensive, everyone has preferences, but attempts to cover the commonly used parts and what sort of things will work.

Avoid cheap parts, especially if mechanical. Invest in quality, you always get what you pay for. Otherwise your entire system might later develop intermittent faults.[1][2] Vertical mount front panel components will need to of a similar height to neatly fit the gap between the PCB and front panel.

In order to construct low profile Eurorack modules vertical mount components are required. These allow the PCB to be mounted parallel to the front panel, keeping module depth to a minimum.[3]

Eurorack panel specifications

The Eurorack format was developed in parallel by Analogue Systems and Doepfer, with different approaches to module power connectors and front panel mounting holes. These days the Doepfer standard predominates.[4][5] The format is based on DIN 41494 Eurocard standard.[6]

Doepfer specifies the Eurorack front panel material as 2 mm anodized aluminium.[7] In practice panels from other manufacturers may slightly differ, e.g. Synthwerks use the closest gauge that Metalphoto offer which is 0.0625" (1.59 mm). Also check data sheets for front panel parts, e.g. the maximum recommended thickness for 3.5 mm Cliff 1384 jacks is 2.5 mm.[8] Front panel dimensions in the the 3U Eurorack format are specified in U and HP not in inches or millimeters. One U (unit) or in German HE (höhen einheit) is 1.75 inches equivalent to 44.45 mm. Thus the panels height is 5.25" (133.35 mm) less any allowance for mounting rail flange. Width is measured in HP (horizontal pitch) or in German TE (teilungs einheiten); 1 HP is 1/5" (0.2", 5.08 mm or 200 mil). The actual width of a front panel is a few tenth of a mm less than whatever multiple of 5.08 mm it is, to give some tolerance for final assembly. A 19-inch rack has a usable width of 84 HP.[6][7][9][10][11]

The vertical space available between mounting rails is:

  • Schroff, 112.2 mm (4.415 inches)
  • Gie-Tec, Proma (now defunct) and TipTop Z-Rails, 112.5mm (4.429 inches)
  • Vector, 115.1mm (4.531 inches)

These don't include a tolerances for the screw hole in the panel nor for the nut in the rail moving up and down. It's better to give a little more clearance than suggested by these figures.[12]

Panel mounting holes

If the Doepfer specification is followed, or rails with sliding nuts are used, elongated holes are not required. These are useful for non-standard panel widths and to compensate for for manufacturing tolerances of the panel width or hole position. They help to fit the modules flush against one another.[13] In a double width case, there will be a gap where the two threaded inserts meet, unless e.g. single 168 HP tiptop Z rails are used.[14]

Oval holes were originally for mixed Analogue Systems (AS) and Doepfer systems. The AS holes are 0.2" from the panel edge and the Doepfer holes are 0.3" (7.62 mm) from the edge. The oval holes were originally used to allow these modules to be placed in the same threaded rows without having the 1/2 HP gap that would otherwise result. These days the oval holes are mostly just centered on the Doepfer spacing.[13]

For front panels up to 10 HP (2 inches) two mounting holes are sufficient, Wider than this and four mounting holes are usual. To attach the modules to the mounting rails M3x6 DIN 7985 cross recessed pan head machine screws are used. The mounting hole diameter is 3.2mm (0.13"), centered 3mm from top and bottom edges and 7.45mm from the left edge. The horizontal distance between the mounting holes has to be a multiple of 5.08mm.[6][7][9]

The vertical distance between the mounting holes on Eurorack rails is 122.5mm apart (4.823"). Based on the manufacturer's drawings for the most common rails used in Euro cases, the clear space between pairs of rails is:

  • 112.2mm, 4.415" = Schroff
  • 112.5mm, 4.429" = Gie-Tec and TipTop Z-Rails
  • 115.1mm, 4.531" = Vector

Those don't include the tolerances (slop) of the nut in the rail moving up and down and the screw hole in the front panel. These can cause the rails to be closer or further apart when any given module is tightened in. It's better to try to give a little more clearance and not count on these exact figures.[12]

Blank panels

See Eurorack DIY parts#Blank panels

PCB dimensions and mounting

These days Eurorack modules tend to mount the PCB parralel to the front panel, held in place by the pots, jacks and switches.[12] Modules with wired front panel components cost more to manufacture than PCB mounted, however these electro-mechanical components have limited lifetimes and while PCB mounted parts can be repaired it's not as easily as wired components. Also PCB mounted components mean the board is designed around specific parts. If any of these parts goes out of production the modules have to be redesigned, with the additional cost of updating the PCBs.[15]

To fit between the mounting rails the maximum vertical PCB size can be from 108mm (4.25") to 110mm. The width of the PCB needs to be a touch less than that of the front panel, whilst allowing for clearance and taking tolerances into consideration.[6][12][3]

Stacked PCBs

Stacked PCBs can be connected with standard 0.1" single and double row male/female pin headers. These combine to a height of 7/16 inch or 11mm and boards can be mounted to each other with spacers of this length.[16]

To cut the headers, don't use tools you value highly, these are made of brittle glass filled epoxy which will damage the edge of any blades used to cut it. To get the single row male headers to length, grip the last pin of the length you want firmly in pliers and snap the rest off. The female headers don't snap easily so first pull the pins out of the body at the point where you want it to snap, then file the ends smooth. Alternately combine smaller lengths to make up the length required. To get them to butt against each other at 0.1" if there is extra plastic on the ends file it down.[16]

Suitable parts can be purchased for example:[16]

  • 517-929974-01-36-RK, Mouser female 2.54mm pin header, 36 way, tin plated copper
  • 517-834-01-36, Mouser male 2.54mm pin header, 36 way, tin plated copper
  • 855-R30-1001102, Mouser M3x11mm hex spacer. Fit to the PCB with M3x5mm machine screws.

Component layout

Choose between having jacks easier to read placed near their associated controls, [10] or below where patch cables are then easier to keep out of the way.

Design the panel so that behind the panel the component bodies have enough clearance from each other and in front both the controls and the users fingers have enough room to operate. Also check that any close to an edge won't interfere with mounting the panel into its enclosure. Check the angle of rotation of the pot will match the scale going to be marked on the panel.[17]

For spacing between 1/4" jacks, a 30 mm x 17 mm center to center grid is comfortable for most people. Most use wide vertical spacing and narrow horizontal spacing. However the opposite allows for placing legends on the side. When marked above or below these are only visible when no plugs are inserted.[18]

Jacks/sockets

3.5mm jack sockets

3.5mm jack sockets not 1/8 inch but are 3.5mm.[19] Popular brands of vertical mount 3.5mm mono jacks for Eurorack are Cliff (used by Doepfer), Erthenvar aka Flight of Harmony, Kobiconn (used by Cwejman, Make Noise, Malekko and Metasonix) and Switchcraft. These are available switched (for normalisation) and unswitched.[15][20] Erthenvar 3.5mm vertical mount jacks with a thread diameter about 5.9mm (0.232"), will fit well with panel drill holes of 6.0 to 6.5mm diameter.[3][21][22] Suppliers:

Cliff horizontal PCB mount

Vertical PCB mount

Vertical mounted potentiometer and two hacked to fit Kobiconn 16PJ138 panel mounting jack sockets in the Harvestman Piston Honda.

Vertical mount 3.5 mm jack sockets are hard to find. Options include:

Wired/panel mount

Banana sockets

Not normally used on unmodified Eurorack,[note 1] banana jack socket are unshielded but CVs don't need shielding and because audio levels are usually high, this won't be a problem. When patching into external synths or other devices use a shielded cable with both ends of the shield connected to ground. Banana sockets are cheaper because they are mechanically simpler. They are also much more durable since there is less to go wrong. They are widely available and come in a range of colours. Banana plugs are stackable i.e. one can plug into the end of another. Most banana synths are designed with stackable plugs in mind, whereas most 1/4" and 3.5mm jack systems include multiples.[23][24]Regular jacks provide an extra switched connection enabling normalization (connections when there is no cable plugged in).[25]

  • Mouser
  • Bushing used where the PCB is parallel to the panel and there isn't enough room behind for the length of the shaft of the banana jack. Obviously this arrangement will protrude further out from the front of panel. Approximate measurements: .32" id, .4" od, .3" high.[26]

Potentiometers and controllers

Vertical mount potentiometers in the WMD Gamma Wave Source. The green one is a BI Technologies P0915N.

Horizontal PCB mount

Vertical PCB mount

  • Thonk:Alpha 9mm Pots
  • Mouser:Alpha RK12L types
  • Mouser:BI Technologies 10.5mm high linear pots
  • Bourns:
    • PDB12-M, PCB mount, 9mm high, no thread, 12mm package
    • PTV09A-4
    • Farnell:3310Y series, 5mm deep with 6mm of thread so may be too low to be used easily
    • PTV111-3 7.5 mm high body with 5.0 mm high bushing, available with centre detent
    • Digital continuous encoders for microcontroller based products
  • Vishay:
    • P12 series 11mm to panel
    • P9 vertical mount 7mm high with 7mm bushing, only up to 10V

Switches

Wired/panel mount

  • SmallBear SKU 0221C1
  • Jameco 317236
    • 0.55" 136241
    • 19.8mm 264990
    • 33.3mm 264946
  • Mouser 633-M201901-RO
    • SP3T toggle switch 633-M202402-RO
    • 633-FB15ANEP2[27]

LEDs

Wired/panel mount

  • Mouser 3mm LED 593-2000C (C stands for clear)[27]

This page uses material from Eurorack DIY parts, which is released under the Creative Commons Attribution-Share-Alike License 3.0. The history of that page before 22 April 2016 serves as the attribution history for the contents of this page before then.

See also

References

  1. ^ On cheap parts..., Muff Wiggler forum, July 2012
  2. ^ The Pitfalls of Choosing Quality Brands of Components?, Muff Wiggler forum, March 2014
  3. ^ a b c 3.5mm Vertical Mount Jacks, Erthenvar
  4. ^ Analogue Systems: Doepfer compatibility, Muff Wiggler forum, October 2009
  5. ^ Analogue Systems or Doepfer as 1st Modular system?, Electro-music.com forum, August 2009
  6. ^ a b c d Some general questions on euro-designing by Graham Hinton, Muff Wiggler forum, October 2011
  7. ^ a b c Doepfer A-100 Construction Details
  8. ^ Aluminum Panel Guage???, Muff Wiggler forum, January 2012
  9. ^ a b confused about euro panel spec standard., Muff Wiggler forum, March 2012
  10. ^ a b Standard measurements in front panels, Electro-music.com forum, May 2007 Cite error: Invalid <ref> tag; name "measures" defined multiple times with different content
  11. ^ Thomas Henry's SN76477 Super Controller Module by Matthias Herman, Electro-music.com forum, July 2007
  12. ^ a b c d Six jacks in euro, what is the preferred configuration?, Muff Wiggler forum, October 2014 Cite error: Invalid <ref> tag; name "six" defined multiple times with different content
  13. ^ a b Euro modules – Oval mounting holes, Muff Wiggler forum, December 2014
  14. ^ The Eurorack Charter?, Muff Wiggler forum, October 2012
  15. ^ a b Plan B/Cliff Jacks, Muff Wiggler forum, September 2008
  16. ^ a b c Hardware for stacked PCBs, Muff Wiggler forum
  17. ^ How i make front panels.
  18. ^ Minimum spacing between 1/4" jacks on DOTCOM modules.. by Andre Majorel on SDIY email list, 18 May 2013
  19. ^ Some Eurorack technical questions, Muff Wiggler forum, April 2011
  20. ^ Have I bought the wrong jacks for eurorack?, Muff Wiggler forum, November 2013
  21. ^ Metasonix R54
  22. ^ Erthenvar 3.5mm Vertical Mount Jacks, Muff Wiggler forum, December 2012
  23. ^ Banana plugs vs. other plugs, Muff Wiggler forum, Oct 2011
  24. ^ [https://www.muffwiggler.com/forum/viewtopic.php?t=42438 Modifying Euro Modules for Banana Jacks], Muff Wiggler forum, Sep 2011
  25. ^ Doepfer - banana conversion, Muff Wiggler forum, March 2010
  26. ^ Banana system pictures, Muff Wiggler forum, 22 Nov 2009
  27. ^ a b BUILD - CGS Euro Modules, Muff Wiggler forum, November 2011

External links

Lists of preferred parts


Cite error: <ref> tags exist for a group named "note", but no corresponding <references group="note"/> tag was found

Retrieved from "https://sdiy.info/wiki/Eurorack_panel_components?oldid=2870"