Search results

[[File:cgs_photo_tubevco2.jpg|thumb|center|500px|The tube VCOs and other tube circuits.]] ...regulator simply because I had one to hand. The second VCO in this module uses the second triode in the 6CG7 as its regulator. ...

...med this circuit is almost identical to Serge's original design. The Serge uses six stages to my four. ...out" output. A second input based on a lag circuit allows square waves and other hard-edged waveforms to be used as the signal source. ...

...ments.|thumb|A Rob Hordijk Original Design modular synthesizer (left) with other instruments. ]] ...triple. It lacks the +/-15V MiniXLR power outlet that is available on the other MIDI triples. The MiniXLR might be used for future expansions, to power e.g ...

...vania) and 6ME8 (apparently GE). These tubes were almost identical to each other, even though they were made by different factories--typical of the tube bus ...lates, the electron beam could be "forced" to switch from one anode to the other; giving a very good ring modulator effect, with reasonable carrier suppress ...

...ut there are also lots of very simple circuits of a VCO, VCA (MC3340), and other effects like fuzz etc. One of the more complicated circuits seems quite out ...e the author states he wrote the book because at the time he couldn't find other books with details of synth circuits in them. There are quite a lot of circ ...

1. Plug the TS-22 into a source of 100-120V AC power. It uses about 25 watts. (Check the label on the back if the unit is wired for 240V, ...commend at least 1/2" space above and below it to allow airflow. The TS-22 uses a 0.5 amp, 5x20mm fast-blow fuse (in 100-120V countries). This fuse should ...

...playing to reach up and tap the keyboard controlling the sequencer. On the other hand, I am quite capable of playing the organ pedal board, but don't becaus Other DIYers have suggested creating a miniature "calculator" style keyboard that ...

...ous functions such as amplitude modulation and for gating signals into the other sections.<ref name="sc82"/> ...e processing, and two outputs. One output is a "squared up" version of the other. This output resembles voltage controlled pulse width modulation (only much ...

The OSC HRM can track 1V/Oct and the module uses a platinum element for temperature stabilization of the pitch curve. Maximu ...ly done with two sine waves (such as the Yamaha DX series) but the OSC HRM uses a bi-quad sine/cosine oscillator at its core and through recursion or feedb ...

This circuit is based on "Nonselective Frequency Tripler Uses Transistor Saturation Characteristics" by R. Lockhart, Jr., in Electronics ...width of these pulses, or move them back and forward with respect to each other, depending in whether the amplitude of the incoming signal or the DC offset ...

* --xml exports an XML dump, uses Special:Export by default when no other xmldump method is specified. * --xmlrevisions uses API:Allrevisions xmldump method. Recommended as it's quicker and puts almos ...

...e outputs, and two separate (unique) digital outputs for use in triggering other circuits. ...ate earth loops. If your panel is mounted directly to an earthed case, and uses jacks with a connection that physically connects to the panel, this resisto ...

...he panel the potentiometer and jack bodies have enough clearance from each other and that in front both the controls and the users fingers have enough room ...5") aluminium sheet. This is easy to machine and isn't too soft. Sometimes other materials are used such as some sheet metal, [[acrylic]] (aka Lucite or Per ...

== Other formats == * LMNC [[Kosmo]] uses 20cm high front panels ...

The circuit uses a standard, non-inverting amplifier configuration. The three modes (HP, BP, ...chosen as they had gains closer to those used in the original design than other frequently used transistors such as the BC547. 2N3904 and 2N3906 have been ...

The circuit uses a standard, non-inverting amplifier configuration. The three modes (HL, BP, ...chosen as they had gains closer to those used in the original design than other frequently used transistors such as the BC547. 2N3904 and 2N3906 have been ...

...out" output. A second input based on a lag circuit allows square waves and other hard-edged waveforms to be used as the signal source. The LM324 op-amps can be replaced by other op-amps in the standard configuration, such as the TL074. ...

...d brick||VBED15, 7805||12 headers on PSU PCB||for non-commercial use only||Uses ready made DC to DC converter||[http://www.dintree.com/#D112 schematic] === Other useful power projects === ...

...al signal by a similar magnet and coil device (acting as a pick-up) at the other end. Some of the vibrations will bounce back and travel up and down the spr ...have recently come to light, with very similar looking tanks/specs to the other makes. ...

...'CGS sequential switch''' is a basic switching/sequencing module with many uses. ...bidirectonal. It can route one of eight signals to its output, but not the other way around. It can also provide independant gate signals for each selected ...