Search results

...hythm and timing accessory. It generates a burst of gate or trigger pulses at various speeds as set from a front panel control. At higher speeds it can be used for washboard, maracas or similar rapid-burst ...

...e 1/f mode, the size of a pitch step is inversely related to the frequency at which it will occur. In other words, the smallest steps are most common, st ...es on a whole new feel, as each of the six shift registers involved shifts at a different rate, according to the 1/f weighting. As such, the second and t ...

* [http://modular.fonik.de/Page37.html EFM files] at Fonitronik Synth DIY ...ectro-music.com/forum/viewtopic.php?t=22255 PCB/Schematic Quick Reference] at electro-music.com ...

Typical Babani pocket-book. Whilst primarily aimed at the guitarist (wah wah, distortion, tremelo etc.), there are comprehensive ...nly suitable for the seasoned synth DIYer, and so is clearly ''NOT'' aimed at beginners!<ref name="ts" /> ...

...to adjust your MIDI-CV converter at this time, to get proper tracking over at least one octave. You would do this by playing first the low C key, adjusti ...ble switching devices, allowing a capacitor to charge, then discharging it at a certain voltage level. By applying a varying voltage to the tube-s grid, ...

...o impose a certain limitation upon yourself. Basically the way I design is at first I go wild, and go complex, until I feel that I've hit some good stuff * 10 April 2015, at Basic Electricity #15, Berlin. Recorded by Matthias Ochs - https://www.yout ...

...wo points results in outputs that always maintain the base control voltage at its full amplitude, mixed with a differing amount of the modulating voltage ...connected to modulated outputs will shift in frequency away from the base, at an amount proportional to its position from the center output. For example, ...

...has an on-board regulator, though a power supply outputting smoothed DC of at least 8 volts will be required. Alternately, the cards could be powered fro <span style="color:#990000;">Build and use this project at your own risk. As individual construction skills, and uses to which this pr ...

...nals can be used to drive the matrix if having more than one switch closed at time is acceptable or desirable. ...ositive direction, as these are in the allowed input range. A second diode at the output of the analog switch prevents the op-amp from driving the output ...

...ound 200 mA at +/-15 volts from the PSU without problems, and notably more at +/-12V output. If using for +/-15 volts there will be minimal heat generate ...tapped transformer (18v-0v-18v) you should be able to pull around 600 mA, at +/-15 volts, from the PSU without problems. There will be a fair amount of ...

[[Printed circuit board|PCBs]] rather than on reducing the cost. Making PCBs at home is much quicker, with results the same day instead of waiting weeks fo ...tion as the dust is extremely fine. Use a vacuum cleaner to catch the dust at source. Safety glasses should always be worn.<ref name="eese" /> ...

...dance line-level input. A mono cable is OK. TS-21 produces a stereo signal at all times to hear the stereo signal, use a 3-wire (ring/tip/sleeve) 1/4" ca ...e how the waveform and its "tone" change. (You might hear a slight crackle at around the 3 o'clock position this is normal for the circuit you do not hav ...

...rm flanges. To mount them into the rack, the face of the panel is extended at the top and bottom by 0.4".<ref name="dotcom">[https://web.archive.org/web/ ...) use fluted dual-dot 1" Moog-style/[[Cosmo Corporation knobs]], available at: ...

...discrete values. In the context of Synth applications, the specific times at which the signals are defined are regular and evenly spaced. ...e slew of reasons why high quality audio signals are sampled and processed at much higher resolutions such as 20- and 24-bits which will be discussed in ...

At the same time as this is happening, there are three other 4 pole analog swi ...the smallest that should be used, though drooping becomes quite noticeable at slow speeds. It may be possible to go as high as 220n for really slow opera ...

...0 to 5 volt waveform, the result will be a sawtooth of twice the frequency at the first output. ...nverted to 5 volts - 5 volts (i.e. 0 volts) where it will continue to rise at the previous rate until it reaches its peak. When the waveform again falls ...

...elopment. And they might have invented the voltage-controlled synthesizer, at a time when Bob Moog and Don Buchla were still sucking on their pacifiers!< ...ube. Some details have been changed, since you want the gas to ionize only at the right time. The grids are designed to shield the anode from the hot cat ...

...ted random switch''', (in memory of Jeff Pontius, this module was designed at his request) is another module for introducing unpredictability into synthe ...of the internal clock, though this can be adjusted to the users preference at construction time - thus the reason why no resistor or capacitor values hav ...

...an exceptionally powerful unit, able to access as many presets as you want at a touch. This means too, that your keyboard will be able to perform non-tem ...for the VER1.0 PCBs. Click through for enlarged, printable versions. Print at 300dpi for correct scaling. Note that the pad in red (one of the GO pads) i ...

2003. Online at [http://www.cim.mcgill.ca/~clark/nordmodularbook/nm_book_toc.html nordmodul Prentice Hall, 1982, {{ISBN|0-13-160630-1}}, Available at [http://thesnowfields.com/manuals/devarahi%20'the%20complete%20guide%20to%2 ...